Porter-Cable Porter Cable BN200SB and FN250SB Manual - Operation and Safety Guidelines

Page 7

FN250SB-BN200SB_9R198001RA_PC_16GA and 18GA FINISH NAILER MANUAL_MAN_JM3_107674RevE_Manua

LOADING THE FN250SBLOADING THE FN250SB

EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.1/CAN/CSA Z94.3 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection.

TO PREVENT ACCIDENTAL INJURIES:

Never place a hand or any other part of the body in nail discharge area of tool while the air supply is connected.

Never point the tool at anyone else.

Never engage in horseplay.

Never pull the trigger unless nose is directed at the work.

Always handle the tool with care.

Do not pull the trigger or depress the trip mechanism while loading the tool.

1. LOAD NAILS:

 

Pull follower back until it latches.

 

(fig. 1)

Pusher

 

Release

(fig. 1)

Follower

Insert nails into track of magazine (fig. 2)

Press pusher release to disengage follower (fig. 3)

(fig. 2)

Pusher

Release

(fig. 3)

-7-

Image 7
Contents FN250SB BN200SB Definitions Safety Guidelines Introduction Safety InstructionsIndexindex Loading Tool AIR Supply and ConnectionsTool Specifications Lubrication Supply SourceRegulator FilterTo Prevent Accidental Injuries Loading the FN250SBLOADING the BN200SBLoad Nails Loading the FN250SBLOADING the FN250SBTool Operation Check Tool OperationSequential Trip Operation Assembly Procedure for Seals Replacement PartsAIR SUPPLY-PRESSURE and Volume BN200SB and FN250SB Fastener Control Adjustment Depth Adjustmentdepth AdjustmentTo Adjust Fastener Control Adjustment Problem Cause Correction Trouble Shootingtrouble ShootingÍndiceíndice Introducción IntroducciónPautas DE Seguridad / Definiciones Suministro DE Aire Y Conexions Instruccionesinstruccionesde Seguridadde SeguridadSuministro DE Aire Y Conexiones AL Cargar LA Herramientaal Cargar LA HerramientaSuministro Suministrode Aire Ydeconexionesaire Y Conexiones Lubricacin Lubricacion Advertencia Para Impedir Lesiones Accidentales Cómo Cargar LAS Herramientascómo CARGARFN250SBEL FN250SB Cargue LOS ClavosVerificación DE LA Operación DE LA Herramienta Operación Deoperaciónla Herramientade LA HerramientaOperacin Operación Operación DE Disparo SecuencialProcedimiento DE Ensamble Para LOS Sellos Presión Y Volumen DEL Suministro DE AireMantenimiento DE LA Herramienta Neumática Partes DE ReemplazoAjuste DEL Control DE Sujetadores Para BN200SB, FN250SB Adjuste DE LA ProfundidadPara Ajustar EL Ajuste DEL Control DE Sujetadores Diagnóstico DE Falladiagnóstico DE Falla ProblemaSommairesommaire Introduction IntroductionMesures DE Sécurité Définitions Fonctionnement Fonctionnement Chargement DECHARGEMENTL’APPAREILDE L’APPAREILConsignes DE Scuritconsignes DE Securite Caract Filtre TuyauxAlimentation EN AIR Comprimé RégulateurChargementchargementdesdes BN200SBSB-1842BN/SB-1850BN Chargement DES Clous Chargementchargementdes FN250SB DU FN250SBSystème DE Sécurité AU COUP-PAR-COUP Fonctionnementfonctionnementde L’APPAREILDE L’OUTILAvant DE Manipuler OU D’UTILISER CET Outil Déclenchement AU COUP-PAR-COUPProcédure D’ASSEMBLAGE DES Garnitures Alimentation D’AIR Pression VolumeEntretien DEENTRETIENL’APPAREILDE L’OUTIL Pneumatique Pièces DE RechangePour Régler LA Commande DE Réglage DE L’ÉLÉMENT ’ASSEMBLAGE Commande DE Réglage Pour LES Modèles BN200SB, FN250SBRéglage DE LA Profondeur Dépannage Problèmes DE Fonctionnement