Grizzly G0501 instruction manual Control Panel

Page 17

Control Panel

T

A

B

S

C

R

D

Q

E

P

O

F

N

G H

M

L

K

J

I

Figure 8. Control panel close-up.

A.EMERGENCY STOP Button—Disconnects power to all motors in the motor cabinet.

B.MAIN BLADE OFF Button—Stops the main saw blade.

C.SCORING BLADE OFF Button—Stops the scoring blade.

L.-Key—Manually decreases the angle of the saw blades in increments of 0.1˚.

M.Set Key—Used to set blade angles entered into the keypad. Also, used for calibration.

N.Digital Display—Displays the current angle of the saw blades.

D.MAIN BLADE DOWN Key—Lowers the height of the main saw blade.

E.SCORING BLADE RIGHT Key—Moves the scoring blade right for alignment purposes.

F.SCORING BLADE DOWN Key—Lowers the height of the scoring blade.

G.C Key—Clears typed entries in the display.

H.Keypad—Keys for inputting the desired angle of the saw blade.

I.Stop Key—Stops the trunnion movement.

J.Start key—Starts trunnion movement after an angle has been entered.

O.SCORING BLADE UP Key—Raises the height of the scoring blade.

P.ARBOR RPM Display—Displays the current RPM of the saw blades.

Q.SCORING BLADE LEFT Key—Moves the scoring blade left for alignment purposes.

R.MAIN BLADE UP Key—Raises the height of the main saw blade.

S.SCORING BLADE ON Button—Starts the scoring blade. Note—The main saw blade must be ON for the scoring blade to start.

T.MAIN BLADE ON Button—Starts the main saw blade.

K. “+Key—Manually increases the angle of the saw blades in increments of 0.1˚.

G0501 Sliding Table Saw

-15-

Image 17
Contents Sliding Table SAW Page Table Of Contents Maintenance Safety Instructions for Power Tools Safety25ft 50ft 100ft Length AMP RatingAdditional Safety Instructions for Table Saws Below are tips to reduce the likelihood of kick- back Preventing KickbackProtecting Yourself From Kickback Glossary Of Terms Commentary General InformationCircuit Requirements 220V 3-PhaseTypical locking type L15-20 plug Receptacle 440V 3-PhaseGrounding Extension Cords To rewire the Model G0501 for 440V opera- tion Rewiring toMain Features Features & ControlsBlades Control Panel Leveling Adjustment Locking Lever Fence Assembly Lock Down LeverRip Fence Controls Blade Guard ControlsAbout this Section Piece Inventory SET UPUnpacking Main CrateSaw unit Crosscut fence components Hardware Recognition Chart Working Clearances Clean Up Site ConsiderationsMoving & Placing Saw Base Unit Control panel correctly set up Table InstallationTo install the sliding table Access panel removed one side Shown To install the blade guard Installing Blade GuardTo install the extension tables Installing Extension TablesLarge extension table installed G0501 Sliding Table Saw Rip Fence To install the rip fenceTo assemble the crosscut table Crosscut TableMounting Shaft Miter Fence To install the miter fenceTest Run To adjust the sliding table parallel with the main blade Sliding Table Parallel AdjustmentTo align the fence scale with the blade Fence Scale AlignmentTo connect the dust ports to a dust collection system Dust CollectionPlease follow these tips Every time you use your saw OperationsOperation Tips To change the blade tilt Changing Blade TiltChanging Blade Speeds To align the scoring blade set Aligning Scoring Blade SetRip cutting with the sliding table Rip CuttingRip fence set even with center Blade G0501 Sliding Table Saw Rip cutting using the traditional table saw techniqueCrosscutting Crosscutting smaller panels Crosscutting using the rip fence as a cut-off gaugeCrosscutting full size panels Miter Cutting Mount the miter fence onto the sliding table To perform a miter cutTo change main blade Changing Main BladeTo change the riving knife Changing Riving KnivesTo change scoring blade set Changing Scoring Blade SetPage Cleaning MaintenanceMiscellaneous BeltsDate Approximate Hours Of Use Maintenance Performed Maintenance LogAbout Service Service AdjustmentsReplacing Belts To change the V-belt on the main motorTo calibrate the blade tilt Calibrating Blade TiltTo change the belt on the scoring blade motor To align the riving knife Adjusting Riving Knife AlignmentRepeat steps Squaring Crosscut Fence to BladeTo square the crosscut fence with the blade Reference Info Aftermarket AccessoriesReplacement Blades Machine Data Sheet Scoring Motor Sliding Table SAW Capacities G0501 Machine Frame Assembly G0501 Machine Frame/Saw Angle Measurement Assemblies G0501 Saw Angle Measurement AssemblyG0501 G0501 Chip Channel Assembly G0501 Saw Blade Adjustment Assembly PSB64M G0501 Main Saw Assemblies Bracket G0501 Scoring Saw Assemblies Description G0501 Swinging Arm Assembly Cleaning Brush 3LIDINGD4ABLEBANDN-ITERT&ENCEN!SSEMBLIES %&HaYc\IVWaZHVl G0501 Crosscut Table Square Plug G0501 Crosscut Fence Helical Pressure Spring G0501 Machine Table Assemblies Extension Table G0501 Rip Fence Assembly TOP Section G0501 Blade Guard Assembly Support ARM G0501 Electrical Panel Components Digital Control Display DP-525 Symptom Possible Cause Possible Solution Motor TroubleshootingPerformance Troubleshooting G0501 Control Panel Back Side Diagram G0501 Electrical Panel Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog