Grizzly G0501 instruction manual Changing Riving Knives, To change the riving knife

Page 49

7.Using the 36mm arbor wrench, remove the arbor nut that secures the main blade (turn clockwise to loosen, as shown in Figure 82).

Figure 82. Removing arbor nut to change blade.

8.Remove the arbor flange and the old main blade.

9.Install the new main blade, replace the arbor flange and nut, and tighten the arbor nut to secure the main blade.

If you changed blade diameter sizes dur- ing this procedure, now is the time to change riving knifes. To do this, follow the instructions titled “Changing Riving Knives” in this manual.

If the kerf thickness is different from your old blade, the scoring blade kerf must be adjusted to match the new main blade kerf. To do this, read the “Changing Scoring Blade Set” and stack the blade inserts to match same thickness as the new blade.

10.Make sure the correct size riving knife is installed and aligned with the blade.

11.Move the orange blade guard back into its original position, next to the blades, and cen- ter the sliding table.

12.Align the scoring blade to the main blade as described in the “Aligning Scoring Blade Set” instructions.

Changing Riving

Knives

The Model G0501 comes with a riving knives for use with 12" and 14" blades.

To change the riving knife:

1.Move the blade tilt to 0˚ on the control panel (blade 90˚ to table), and raise the main blade as far as it will go.

2.Disconnect the saw from the power source!

3.Move the sliding table all the way to the left and push the release knob to expose the internal blade guard (Figure 83) that covers the blades and riving knife.

Blade Guard

Figure 83. Blade guard exposed to access

riving knife.

4.Pull the blade guard away from the riving knife to expose the mounting assembly. (The internal blade guard is held in place with a magnet.)

5.Remove the center bolt (Figure 84) in the mounting assembly to remove the mounting plate.

6.Remove the currently installed riving knife and install the correct riving knife.

G0501 Sliding Table Saw

-47-

Image 49
Contents Sliding Table SAW Page Table Of Contents Maintenance Safety Instructions for Power Tools Safety25ft 50ft 100ft Length AMP RatingAdditional Safety Instructions for Table Saws Protecting Yourself From Kickback Preventing KickbackBelow are tips to reduce the likelihood of kick- back Glossary Of Terms Commentary General InformationCircuit Requirements 220V 3-PhaseTypical locking type L15-20 plug Receptacle 440V 3-PhaseGrounding Extension Cords To rewire the Model G0501 for 440V opera- tion Rewiring toMain Features Features & ControlsBlades Control Panel Leveling Adjustment Locking Lever Fence Assembly Lock Down LeverRip Fence Controls Blade Guard ControlsAbout this Section Piece Inventory SET UPUnpacking Main CrateSaw unit Crosscut fence components Hardware Recognition Chart Working Clearances Clean Up Site ConsiderationsMoving & Placing Saw Base Unit Control panel correctly set up Table InstallationTo install the sliding table Access panel removed one side Shown To install the blade guard Installing Blade GuardTo install the extension tables Installing Extension TablesLarge extension table installed G0501 Sliding Table Saw Rip Fence To install the rip fenceTo assemble the crosscut table Crosscut TableMounting Shaft Miter Fence To install the miter fenceTest Run To adjust the sliding table parallel with the main blade Sliding Table Parallel AdjustmentTo align the fence scale with the blade Fence Scale AlignmentTo connect the dust ports to a dust collection system Dust CollectionOperation Tips OperationsPlease follow these tips Every time you use your saw Changing Blade Speeds Changing Blade TiltTo change the blade tilt To align the scoring blade set Aligning Scoring Blade SetRip cutting with the sliding table Rip CuttingRip fence set even with center Blade G0501 Sliding Table Saw Rip cutting using the traditional table saw techniqueCrosscutting Crosscutting full size panels Crosscutting using the rip fence as a cut-off gaugeCrosscutting smaller panels Miter Cutting Mount the miter fence onto the sliding table To perform a miter cutTo change main blade Changing Main BladeTo change the riving knife Changing Riving KnivesTo change scoring blade set Changing Scoring Blade SetPage Cleaning MaintenanceMiscellaneous BeltsDate Approximate Hours Of Use Maintenance Performed Maintenance LogAbout Service Service AdjustmentsReplacing Belts To change the V-belt on the main motorTo change the belt on the scoring blade motor Calibrating Blade TiltTo calibrate the blade tilt To align the riving knife Adjusting Riving Knife AlignmentTo square the crosscut fence with the blade Squaring Crosscut Fence to BladeRepeat steps Replacement Blades Aftermarket AccessoriesReference Info Machine Data Sheet Scoring Motor Sliding Table SAW Capacities G0501 Machine Frame Assembly G0501 Machine Frame/Saw Angle Measurement Assemblies G0501 Saw Angle Measurement AssemblyG0501 G0501 Chip Channel Assembly G0501 Saw Blade Adjustment Assembly PSB64M G0501 Main Saw Assemblies Bracket G0501 Scoring Saw Assemblies Description G0501 Swinging Arm Assembly Cleaning Brush 3LIDINGD4ABLEBANDN-ITERT&ENCEN!SSEMBLIES %&HaYc\IVWaZHVl G0501 Crosscut Table Square Plug G0501 Crosscut Fence Helical Pressure Spring G0501 Machine Table Assemblies Extension Table G0501 Rip Fence Assembly TOP Section G0501 Blade Guard Assembly Support ARM G0501 Electrical Panel Components Digital Control Display DP-525 Symptom Possible Cause Possible Solution Motor TroubleshootingPerformance Troubleshooting G0501 Control Panel Back Side Diagram G0501 Electrical Panel Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog