Grizzly G0501 instruction manual Aligning Scoring Blade Set, To align the scoring blade set

Page 41

4.Position the V-belt in one of the pulley loca- tions illustrated in Figure 62, depending on your desired blade speed.

5000

3000

4000

6000

Figure 62. Belt speed diagram.

5.Turn the pulley speed switch (Figure 63) so that the opening in the fins line up with the belt position. This switch registers the speed with the control panel.

Pulley Speed

Switch

Figure 63. Pulley speed switch.

6.Move the belt tension handle up to tighten the V-belt.

7.Close and secure the motor cabinet door.

Aligning Scoring

Blade Set

The scoring blade must be aligned with the main blade to ensure satisfactory cutting results. Before attempting to align the scoring blade with the main blade, the kerf thickness must match that of the main blade.

To align the scoring blade set:

1.Move the blade tilt to 0˚ on the control panel (blade 90˚ to table), and raise the main blade and scoring blade set up as far as they will go.

2.Remove the stop bolt from the rip fence, and move the rip fence against the main blade (or scoring blade) as shown in Figure 64.

Figure 64. Fence against blade as a guide for

aligning the scoring blade.

3.Use the control panel to move the scoring blade so that the rip fence can touch both the scoring blade and the main blade when posi- tioned as shown in Figure 64.

4.Lower the scoring blade to the correct height and perform a test cut, then make any final adjustments.

G0501 Sliding Table Saw

-39-

Image 41

Contents Sliding Table SAW Page Table Of Contents Maintenance Safety Instructions for Power Tools Safety25ft 50ft 100ft Length AMP RatingAdditional Safety Instructions for Table Saws Below are tips to reduce the likelihood of kick- back Preventing KickbackProtecting Yourself From Kickback Glossary Of Terms Commentary General InformationCircuit Requirements 220V 3-PhaseTypical locking type L15-20 plug Receptacle 440V 3-PhaseGrounding Extension Cords To rewire the Model G0501 for 440V opera- tion Rewiring toMain Features Features & ControlsBlades Control Panel Leveling Adjustment Locking Lever Fence Assembly Lock Down LeverRip Fence Controls Blade Guard ControlsAbout this Section Piece Inventory SET UPUnpacking Main CrateSaw unit Crosscut fence components Hardware Recognition Chart Working Clearances Clean Up Site ConsiderationsMoving & Placing Saw Base Unit Control panel correctly set up Table InstallationTo install the sliding table Access panel removed one side Shown To install the blade guard Installing Blade GuardTo install the extension tables Installing Extension TablesLarge extension table installed G0501 Sliding Table Saw Rip Fence To install the rip fenceTo assemble the crosscut table Crosscut TableMounting Shaft Miter Fence To install the miter fenceTest Run To adjust the sliding table parallel with the main blade Sliding Table Parallel AdjustmentTo align the fence scale with the blade Fence Scale AlignmentTo connect the dust ports to a dust collection system Dust CollectionPlease follow these tips Every time you use your saw OperationsOperation Tips To change the blade tilt Changing Blade TiltChanging Blade Speeds To align the scoring blade set Aligning Scoring Blade SetRip cutting with the sliding table Rip CuttingRip fence set even with center Blade G0501 Sliding Table Saw Rip cutting using the traditional table saw techniqueCrosscutting Crosscutting smaller panels Crosscutting using the rip fence as a cut-off gaugeCrosscutting full size panels Miter Cutting Mount the miter fence onto the sliding table To perform a miter cutTo change main blade Changing Main BladeTo change the riving knife Changing Riving KnivesTo change scoring blade set Changing Scoring Blade SetPage Cleaning MaintenanceMiscellaneous BeltsDate Approximate Hours Of Use Maintenance Performed Maintenance LogAbout Service Service AdjustmentsReplacing Belts To change the V-belt on the main motorTo calibrate the blade tilt Calibrating Blade TiltTo change the belt on the scoring blade motor To align the riving knife Adjusting Riving Knife AlignmentRepeat steps Squaring Crosscut Fence to BladeTo square the crosscut fence with the blade Reference Info Aftermarket AccessoriesReplacement Blades Machine Data Sheet Scoring Motor Sliding Table SAW Capacities G0501 Machine Frame Assembly G0501 Machine Frame/Saw Angle Measurement Assemblies G0501 Saw Angle Measurement AssemblyG0501 G0501 Chip Channel Assembly G0501 Saw Blade Adjustment Assembly PSB64M G0501 Main Saw Assemblies Bracket G0501 Scoring Saw Assemblies Description G0501 Swinging Arm Assembly Cleaning Brush 3LIDINGD4ABLEBANDN-ITERT&ENCEN!SSEMBLIES %&HaYc\IVWaZHVl G0501 Crosscut Table Square Plug G0501 Crosscut Fence Helical Pressure Spring G0501 Machine Table Assemblies Extension Table G0501 Rip Fence Assembly TOP Section G0501 Blade Guard Assembly Support ARM G0501 Electrical Panel Components Digital Control Display DP-525 Symptom Possible Cause Possible Solution Motor TroubleshootingPerformance Troubleshooting G0501 Control Panel Back Side Diagram G0501 Electrical Panel Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog