Grizzly instruction manual Large extension table installed G0501 Sliding Table Saw

Page 30

2.Remove the three cap screws, lock washers and flat washers from the side of the table (Figure 38, white arrows) and remove the two cap screws from the motor cabinet (Figure 38, black arrows).

6.Check the surfaces of the table with a straight edge a shown in Figure 40.

Figure 38. Hardware location for small table.

3.Position the small extension table over the holes on the cast iron table and secure it with the three cap screws that you removed in step 2 (Figure 39). Note—Get assistance positioning the table and holding it in place while installing.

Cap Screws

Adjustment Screws

Figure 39. Small extension table installed.

4.Use the adjustment screws (Figure 39) under the extension table to level the top sur- face with the saw table.

5.When the surfaces are level, slide the table supports against the machine frame and secure them with the cap screws.

Figure 40. Checking with a straight edge.

7.Position the adjustment screws between the table support braces and extension table to finely tune the table so it is level.

8.To install the large extension table, move to the back of the saw and remove the four cap screws from cast iron table and the four cap screws from the cabinet.

9.With the help of at least two assistants, install and level the large extension table in the same manner as the small extension table, using the hardware removed in step 8. Figure 41 shows the large extension table installed correctly.

Figure 41. Large extension table installed.

-28-

G0501 Sliding Table Saw

Image 30
Contents Sliding Table SAW Page Table Of Contents Maintenance Safety Safety Instructions for Power ToolsLength AMP Rating 25ft 50ft 100ftAdditional Safety Instructions for Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to reduce the likelihood of kick- back Glossary Of Terms General Information Commentary220V 3-Phase Circuit Requirements440V 3-Phase Typical locking type L15-20 plug ReceptacleGrounding Extension Cords Rewiring to To rewire the Model G0501 for 440V opera- tionFeatures & Controls Main FeaturesBlades Control Panel Rip Fence Controls Fence Assembly Lock Down LeverLeveling Adjustment Locking Lever Blade Guard ControlsUnpacking SET UPAbout this Section Piece Inventory Main CrateSaw unit Crosscut fence components Hardware Recognition Chart Clean Up Site Considerations Working ClearancesMoving & Placing Saw Base Unit Table Installation Control panel correctly set upTo install the sliding table Access panel removed one side Shown Installing Blade Guard To install the blade guardInstalling Extension Tables To install the extension tablesLarge extension table installed G0501 Sliding Table Saw To install the rip fence Rip FenceCrosscut Table To assemble the crosscut tableMounting Shaft To install the miter fence Miter FenceTest Run Sliding Table Parallel Adjustment To adjust the sliding table parallel with the main bladeFence Scale Alignment To align the fence scale with the bladeDust Collection To connect the dust ports to a dust collection systemOperations Operation TipsPlease follow these tips Every time you use your saw Changing Blade Tilt Changing Blade SpeedsTo change the blade tilt Aligning Scoring Blade Set To align the scoring blade setRip Cutting Rip cutting with the sliding tableRip cutting using the traditional table saw technique Rip fence set even with center Blade G0501 Sliding Table SawCrosscutting Crosscutting using the rip fence as a cut-off gauge Crosscutting full size panelsCrosscutting smaller panels Miter Cutting To perform a miter cut Mount the miter fence onto the sliding tableChanging Main Blade To change main bladeChanging Riving Knives To change the riving knifeChanging Scoring Blade Set To change scoring blade setPage Miscellaneous MaintenanceCleaning BeltsMaintenance Log Date Approximate Hours Of Use Maintenance PerformedReplacing Belts Service AdjustmentsAbout Service To change the V-belt on the main motorCalibrating Blade Tilt To change the belt on the scoring blade motorTo calibrate the blade tilt Adjusting Riving Knife Alignment To align the riving knifeSquaring Crosscut Fence to Blade To square the crosscut fence with the bladeRepeat steps Aftermarket Accessories Replacement BladesReference Info Machine Data Sheet Scoring Motor Sliding Table SAW Capacities G0501 Machine Frame Assembly G0501 Saw Angle Measurement Assembly G0501 Machine Frame/Saw Angle Measurement AssembliesG0501 G0501 Chip Channel Assembly G0501 Saw Blade Adjustment Assembly PSB64M G0501 Main Saw Assemblies Bracket G0501 Scoring Saw Assemblies Description G0501 Swinging Arm Assembly Cleaning Brush 3LIDINGD4ABLEBANDN-ITERT&ENCEN!SSEMBLIES %&HaYc\IVWaZHVl G0501 Crosscut Table Square Plug G0501 Crosscut Fence Helical Pressure Spring G0501 Machine Table Assemblies Extension Table G0501 Rip Fence Assembly TOP Section G0501 Blade Guard Assembly Support ARM G0501 Electrical Panel Components Digital Control Display DP-525 Motor Troubleshooting Symptom Possible Cause Possible SolutionPerformance Troubleshooting G0501 Control Panel Back Side Diagram G0501 Electrical Panel Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WAPage Call Today For a Free Full Color Catalog