Grizzly G0501 instruction manual Table Installation, Control panel correctly set up

Page 25

Setting Up Control

Panel

To set up the control panel:

1. Using a 6mm hex wrench, remove the red control panel shipping brace shown in Figure 21.

Figure 21. Control panel shipping brace.

2. Remove the three cap screws on the face of the control panel to open the cover.

3. Remove the three cap screws and nuts from the inside left edge of the control panel (Figure 22).

Figure 22. Control panel face and side cap

screws.

G0501 Sliding Table Saw

4.Swing the control panel against the frame of the saw and secure it in place with the three caps screws that you removed from the inside of the control panel in step 3.

5.Close the control panel face and secure it with the three cap screws that originally kept it closed, so the control panel is set up simi- lar to the photo in Figure 23.

Figure 23. Control panel correctly set up.

Table Installation

Installing the sliding table is a difficult procedure because the sliding table is very heavy and because the attachment blocks inside the table need to be aligned with the attachment holes on the bottom of the table.

The sliding table for the Model G0501 weighs over 350 lbs. Use at least four strong people to lift it in position. Improper lifting techniques or inadequate lifting assis- tance could result in serious crushing or strain injuries.

-23-

Image 25

Contents Sliding Table SAW Page Table Of Contents Maintenance Safety Instructions for Power Tools Safety25ft 50ft 100ft Length AMP RatingAdditional Safety Instructions for Table Saws Protecting Yourself From Kickback Preventing KickbackBelow are tips to reduce the likelihood of kick- back Glossary Of Terms Commentary General InformationCircuit Requirements 220V 3-PhaseTypical locking type L15-20 plug Receptacle 440V 3-PhaseGrounding Extension Cords To rewire the Model G0501 for 440V opera- tion Rewiring toMain Features Features & ControlsBlades Control Panel Leveling Adjustment Locking Lever Fence Assembly Lock Down LeverRip Fence Controls Blade Guard ControlsAbout this Section Piece Inventory SET UPUnpacking Main CrateSaw unit Crosscut fence components Hardware Recognition Chart Working Clearances Clean Up Site ConsiderationsMoving & Placing Saw Base Unit Control panel correctly set up Table InstallationTo install the sliding table Access panel removed one side Shown To install the blade guard Installing Blade GuardTo install the extension tables Installing Extension TablesLarge extension table installed G0501 Sliding Table Saw Rip Fence To install the rip fenceTo assemble the crosscut table Crosscut TableMounting Shaft Miter Fence To install the miter fenceTest Run To adjust the sliding table parallel with the main blade Sliding Table Parallel AdjustmentTo align the fence scale with the blade Fence Scale AlignmentTo connect the dust ports to a dust collection system Dust CollectionOperation Tips OperationsPlease follow these tips Every time you use your saw Changing Blade Speeds Changing Blade TiltTo change the blade tilt To align the scoring blade set Aligning Scoring Blade SetRip cutting with the sliding table Rip CuttingRip fence set even with center Blade G0501 Sliding Table Saw Rip cutting using the traditional table saw techniqueCrosscutting Crosscutting full size panels Crosscutting using the rip fence as a cut-off gaugeCrosscutting smaller panels Miter Cutting Mount the miter fence onto the sliding table To perform a miter cutTo change main blade Changing Main BladeTo change the riving knife Changing Riving KnivesTo change scoring blade set Changing Scoring Blade SetPage Cleaning MaintenanceMiscellaneous BeltsDate Approximate Hours Of Use Maintenance Performed Maintenance LogAbout Service Service AdjustmentsReplacing Belts To change the V-belt on the main motorTo change the belt on the scoring blade motor Calibrating Blade TiltTo calibrate the blade tilt To align the riving knife Adjusting Riving Knife AlignmentTo square the crosscut fence with the blade Squaring Crosscut Fence to BladeRepeat steps Replacement Blades Aftermarket AccessoriesReference Info Machine Data Sheet Scoring Motor Sliding Table SAW Capacities G0501 Machine Frame Assembly G0501 Machine Frame/Saw Angle Measurement Assemblies G0501 Saw Angle Measurement AssemblyG0501 G0501 Chip Channel Assembly G0501 Saw Blade Adjustment Assembly PSB64M G0501 Main Saw Assemblies Bracket G0501 Scoring Saw Assemblies Description G0501 Swinging Arm Assembly Cleaning Brush 3LIDINGD4ABLEBANDN-ITERT&ENCEN!SSEMBLIES %&HaYc\IVWaZHVl G0501 Crosscut Table Square Plug G0501 Crosscut Fence Helical Pressure Spring G0501 Machine Table Assemblies Extension Table G0501 Rip Fence Assembly TOP Section G0501 Blade Guard Assembly Support ARM G0501 Electrical Panel Components Digital Control Display DP-525 Symptom Possible Cause Possible Solution Motor TroubleshootingPerformance Troubleshooting G0501 Control Panel Back Side Diagram G0501 Electrical Panel Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog