Grizzly G0501 instruction manual Clean Up Site Considerations, Working Clearances

Page 23

Clean Up		Site Considerations

The unpainted surfaces are coated with a waxy oil to protect them from corrosion during ship- ment. Remove this protective coating with a sol- vent cleaner or citrus-based degreaser such as Grizzly’s G7895 Degreaser. To clean thoroughly, some parts may need to be removed. For opti- mum performance from your machine, make sure you clean all moving parts or sliding contact surfaces that are coated. Avoid chlo- rine-based solvents as they may damage painted surfaces should they come in contact. Always fol- low the manufacturer’s instructions when using any type of cleaning product.

Gasoline and petroleum products have low flash points and could cause an explosion or fire if

used to clean machinery. DO NOT use gasoline or petroleum products to clean the machinery.

Smoking near solvents could ignite an explosion or fire and cause serious injury. DO NOT smoke while using solvents.

Floor Load

The Model G0501 weighs 2314 lbs. and has a base footprint of 641⁄2" W x 39" D. Most commer- cial floors are suitable for your machine. Some residential floors may require additional reinforce- ment to support both the machine and operator.

Working Clearances

Consider existing and anticipated needs, size of material to be processed through each machine, and space for auxiliary stands, work tables or other machinery when establishing a location for your saw. See Figure 18 for the maximum work- ing clearances of the Model G0501.

193" (Fully Extended)

243.5"

Figure 18. Working clearances.

Many of the solvents commonly used to clean machinery can be toxic when inhaled or ingest- ed. Lack of ventilation while using these sol- vents could cause seri- ous personal health risks or fire. Take precautions from this hazard by only using cleaning solvents in a well ventilated area.

G0501 Sliding Table Saw

Unsupervised children and visitors inside your shop could cause serious person- al injury to themselves. Lock all entrances to the shop when you are away and DO NOT allow unsupervised children or visitors in your shop at any time!

-21-

Image 23

Contents Sliding Table SAW Page Table Of Contents Maintenance Safety Instructions for Power Tools Safety25ft 50ft 100ft Length AMP RatingAdditional Safety Instructions for Table Saws Below are tips to reduce the likelihood of kick- back Preventing KickbackProtecting Yourself From Kickback Glossary Of Terms Commentary General InformationCircuit Requirements 220V 3-PhaseTypical locking type L15-20 plug Receptacle 440V 3-PhaseGrounding Extension Cords To rewire the Model G0501 for 440V opera- tion Rewiring toMain Features Features & ControlsBlades Control Panel Blade Guard Controls Fence Assembly Lock Down LeverLeveling Adjustment Locking Lever Rip Fence ControlsMain Crate SET UPAbout this Section Piece Inventory UnpackingSaw unit Crosscut fence components Hardware Recognition Chart Working Clearances Clean Up Site ConsiderationsMoving & Placing Saw Base Unit Control panel correctly set up Table InstallationTo install the sliding table Access panel removed one side Shown To install the blade guard Installing Blade GuardTo install the extension tables Installing Extension TablesLarge extension table installed G0501 Sliding Table Saw Rip Fence To install the rip fenceTo assemble the crosscut table Crosscut TableMounting Shaft Miter Fence To install the miter fenceTest Run To adjust the sliding table parallel with the main blade Sliding Table Parallel AdjustmentTo align the fence scale with the blade Fence Scale AlignmentTo connect the dust ports to a dust collection system Dust CollectionPlease follow these tips Every time you use your saw OperationsOperation Tips To change the blade tilt Changing Blade TiltChanging Blade Speeds To align the scoring blade set Aligning Scoring Blade SetRip cutting with the sliding table Rip CuttingRip fence set even with center Blade G0501 Sliding Table Saw Rip cutting using the traditional table saw techniqueCrosscutting Crosscutting smaller panels Crosscutting using the rip fence as a cut-off gaugeCrosscutting full size panels Miter Cutting Mount the miter fence onto the sliding table To perform a miter cutTo change main blade Changing Main BladeTo change the riving knife Changing Riving KnivesTo change scoring blade set Changing Scoring Blade SetPage Belts MaintenanceCleaning MiscellaneousDate Approximate Hours Of Use Maintenance Performed Maintenance LogTo change the V-belt on the main motor Service AdjustmentsAbout Service Replacing BeltsTo calibrate the blade tilt Calibrating Blade TiltTo change the belt on the scoring blade motor To align the riving knife Adjusting Riving Knife AlignmentRepeat steps Squaring Crosscut Fence to BladeTo square the crosscut fence with the blade Reference Info Aftermarket AccessoriesReplacement Blades Machine Data Sheet Scoring Motor Sliding Table SAW Capacities G0501 Machine Frame Assembly G0501 Machine Frame/Saw Angle Measurement Assemblies G0501 Saw Angle Measurement AssemblyG0501 G0501 Chip Channel Assembly G0501 Saw Blade Adjustment Assembly PSB64M G0501 Main Saw Assemblies Bracket G0501 Scoring Saw Assemblies Description G0501 Swinging Arm Assembly Cleaning Brush 3LIDINGD4ABLEBANDN-ITERT&ENCEN!SSEMBLIES %&HaYc\IVWaZHVl G0501 Crosscut Table Square Plug G0501 Crosscut Fence Helical Pressure Spring G0501 Machine Table Assemblies Extension Table G0501 Rip Fence Assembly TOP Section G0501 Blade Guard Assembly Support ARM G0501 Electrical Panel Components Digital Control Display DP-525 Symptom Possible Cause Possible Solution Motor TroubleshootingPerformance Troubleshooting G0501 Control Panel Back Side Diagram G0501 Electrical Panel Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog