Grizzly G0501 instruction manual Miter Fence, To install the miter fence

Page 34

Miter Fence

To install the miter fence:

1.Loosen the clamp plate with the ratchet han- dle to prepare the miter fence for installation.

2.Align the fixed bolt in the slot closest to the blade and align the clamp plate in the other slot as shown in Figure 51.

Fixed Bolt

Clamp Plate

Figure 51. Miter fence components aligned for

installation of miter fence.

3.Thread the fixed bolt into the fixed block. The miter fence should now slide up and down the angle range freely.

4.Position the fence at the desired angle and use the clamp plate ratcheting handle to lock the fence in place. Figure 52 shows the miter fence set to 45˚ on the miter fence scale.

Figure 52. Miter fence set to 45˚ mark on the

miter gauge scale.

-32-

G0501 Sliding Table Saw

Image 34
Contents Sliding Table SAW Page Table Of Contents Maintenance Safety Safety Instructions for Power ToolsLength AMP Rating 25ft 50ft 100ftAdditional Safety Instructions for Table Saws Protecting Yourself From Kickback Preventing KickbackBelow are tips to reduce the likelihood of kick- back Glossary Of Terms General Information Commentary220V 3-Phase Circuit Requirements440V 3-Phase Typical locking type L15-20 plug ReceptacleGrounding Extension Cords Rewiring to To rewire the Model G0501 for 440V opera- tionFeatures & Controls Main FeaturesBlades Control Panel Rip Fence Controls Fence Assembly Lock Down LeverLeveling Adjustment Locking Lever Blade Guard ControlsUnpacking SET UPAbout this Section Piece Inventory Main CrateSaw unit Crosscut fence components Hardware Recognition Chart Clean Up Site Considerations Working ClearancesMoving & Placing Saw Base Unit Table Installation Control panel correctly set upTo install the sliding table Access panel removed one side Shown Installing Blade Guard To install the blade guardInstalling Extension Tables To install the extension tablesLarge extension table installed G0501 Sliding Table Saw To install the rip fence Rip FenceCrosscut Table To assemble the crosscut tableMounting Shaft To install the miter fence Miter FenceTest Run Sliding Table Parallel Adjustment To adjust the sliding table parallel with the main bladeFence Scale Alignment To align the fence scale with the bladeDust Collection To connect the dust ports to a dust collection systemOperation Tips OperationsPlease follow these tips Every time you use your saw Changing Blade Speeds Changing Blade TiltTo change the blade tilt Aligning Scoring Blade Set To align the scoring blade setRip Cutting Rip cutting with the sliding tableRip cutting using the traditional table saw technique Rip fence set even with center Blade G0501 Sliding Table SawCrosscutting Crosscutting full size panels Crosscutting using the rip fence as a cut-off gaugeCrosscutting smaller panels Miter Cutting To perform a miter cut Mount the miter fence onto the sliding tableChanging Main Blade To change main bladeChanging Riving Knives To change the riving knifeChanging Scoring Blade Set To change scoring blade setPage Miscellaneous MaintenanceCleaning BeltsMaintenance Log Date Approximate Hours Of Use Maintenance PerformedReplacing Belts Service AdjustmentsAbout Service To change the V-belt on the main motorTo change the belt on the scoring blade motor Calibrating Blade TiltTo calibrate the blade tilt Adjusting Riving Knife Alignment To align the riving knifeTo square the crosscut fence with the blade Squaring Crosscut Fence to BladeRepeat steps Replacement Blades Aftermarket AccessoriesReference Info Machine Data Sheet Scoring Motor Sliding Table SAW Capacities G0501 Machine Frame Assembly G0501 Saw Angle Measurement Assembly G0501 Machine Frame/Saw Angle Measurement AssembliesG0501 G0501 Chip Channel Assembly G0501 Saw Blade Adjustment Assembly PSB64M G0501 Main Saw Assemblies Bracket G0501 Scoring Saw Assemblies Description G0501 Swinging Arm Assembly Cleaning Brush 3LIDINGD4ABLEBANDN-ITERT&ENCEN!SSEMBLIES %&HaYc\IVWaZHVl G0501 Crosscut Table Square Plug G0501 Crosscut Fence Helical Pressure Spring G0501 Machine Table Assemblies Extension Table G0501 Rip Fence Assembly TOP Section G0501 Blade Guard Assembly Support ARM G0501 Electrical Panel Components Digital Control Display DP-525 Motor Troubleshooting Symptom Possible Cause Possible SolutionPerformance Troubleshooting G0501 Control Panel Back Side Diagram G0501 Electrical Panel Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WAPage Call Today For a Free Full Color Catalog