Grizzly G0501 instruction manual Crosscut Table, To assemble the crosscut table

Page 32

7.Check if the bottom edge of the aluminum fence piece rests on the top surface of the table. Note—The aluminum fence piece will scratch the table surface if the ride height is not adjusted correctly.

If the bottom edge of the aluminum fence piece does not rest on the table, then fence is correctly adjusted. Proceed to the next sub-section.

If the bottom edge of the aluminum fence piece does rest on the table, then contin- ue on to the next step.

8.Loosen the cam bolt located on the end of the fence clamp assembly (see Figure 45).

Figure 45. Installed clamp assembly.

9.Rotate the cam up or down to adjust the ride height of the fence.

10.Retighten the cam bolt and check the ride height. Re-adjust if necessary.

Crosscut Table

To assemble the crosscut table:

1.Swing the crosscut table brace away from the table saw base. Note—A magnet holds the support against the base. A strong pull is necessary to free the support.

2.Position the brace perpendicular to the long edge of the sliding table.

3.One end of the crosscut table has a clamp- ing assembly designed to attach to the bar on the sliding table. The two cap screws (Figure 46) located under the clamp need to be backed out far enough to allow the clamp to slip over the bar on the sliding table.

Figure 46. Cap screws used to secure the

crosscut table clamping assembly.

4.Lift the crosscut table and slip the clamp over the bar on the sliding table and set the other end of the crosscut table onto the shaft that protrudes up from the brace (Figure 47).

-30-

G0501 Sliding Table Saw

Image 32
Contents Sliding Table SAW Page Table Of Contents Maintenance Safety Safety Instructions for Power ToolsLength AMP Rating 25ft 50ft 100ftAdditional Safety Instructions for Table Saws Below are tips to reduce the likelihood of kick- back Preventing KickbackProtecting Yourself From Kickback Glossary Of Terms General Information Commentary220V 3-Phase Circuit Requirements440V 3-Phase Typical locking type L15-20 plug ReceptacleGrounding Extension Cords Rewiring to To rewire the Model G0501 for 440V opera- tionFeatures & Controls Main FeaturesBlades Control Panel Fence Assembly Lock Down Lever Leveling Adjustment Locking LeverRip Fence Controls Blade Guard ControlsSET UP About this Section Piece InventoryUnpacking Main CrateSaw unit Crosscut fence components Hardware Recognition Chart Clean Up Site Considerations Working ClearancesMoving & Placing Saw Base Unit Table Installation Control panel correctly set upTo install the sliding table Access panel removed one side Shown Installing Blade Guard To install the blade guardInstalling Extension Tables To install the extension tablesLarge extension table installed G0501 Sliding Table Saw To install the rip fence Rip FenceCrosscut Table To assemble the crosscut tableMounting Shaft To install the miter fence Miter FenceTest Run Sliding Table Parallel Adjustment To adjust the sliding table parallel with the main bladeFence Scale Alignment To align the fence scale with the bladeDust Collection To connect the dust ports to a dust collection systemPlease follow these tips Every time you use your saw OperationsOperation Tips To change the blade tilt Changing Blade TiltChanging Blade Speeds Aligning Scoring Blade Set To align the scoring blade setRip Cutting Rip cutting with the sliding tableRip cutting using the traditional table saw technique Rip fence set even with center Blade G0501 Sliding Table SawCrosscutting Crosscutting smaller panels Crosscutting using the rip fence as a cut-off gaugeCrosscutting full size panels Miter Cutting To perform a miter cut Mount the miter fence onto the sliding tableChanging Main Blade To change main bladeChanging Riving Knives To change the riving knifeChanging Scoring Blade Set To change scoring blade setPage Maintenance CleaningMiscellaneous BeltsMaintenance Log Date Approximate Hours Of Use Maintenance PerformedService Adjustments About ServiceReplacing Belts To change the V-belt on the main motorTo calibrate the blade tilt Calibrating Blade TiltTo change the belt on the scoring blade motor Adjusting Riving Knife Alignment To align the riving knifeRepeat steps Squaring Crosscut Fence to BladeTo square the crosscut fence with the blade Reference Info Aftermarket AccessoriesReplacement Blades Machine Data Sheet Scoring Motor Sliding Table SAW Capacities G0501 Machine Frame Assembly G0501 Saw Angle Measurement Assembly G0501 Machine Frame/Saw Angle Measurement AssembliesG0501 G0501 Chip Channel Assembly G0501 Saw Blade Adjustment Assembly PSB64M G0501 Main Saw Assemblies Bracket G0501 Scoring Saw Assemblies Description G0501 Swinging Arm Assembly Cleaning Brush 3LIDINGD4ABLEBANDN-ITERT&ENCEN!SSEMBLIES %&HaYc\IVWaZHVl G0501 Crosscut Table Square Plug G0501 Crosscut Fence Helical Pressure Spring G0501 Machine Table Assemblies Extension Table G0501 Rip Fence Assembly TOP Section G0501 Blade Guard Assembly Support ARM G0501 Electrical Panel Components Digital Control Display DP-525 Motor Troubleshooting Symptom Possible Cause Possible SolutionPerformance Troubleshooting G0501 Control Panel Back Side Diagram G0501 Electrical Panel Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WAPage Call Today For a Free Full Color Catalog