Grizzly G0501 To perform a miter cut, Mount the miter fence onto the sliding table

Page 47

To perform a miter cut:

1.Mount the miter fence onto the sliding table.

2.Position the fence at the desired angle and use the clamp plate ratcheting handle to lock the fence in place. Figure 76 shows the miter fence set to 45˚ on the miter fence scale.

Clamp Plate

Ratcheting Handle

4.Position the flip stop according to the length of the workpiece you want to cut off to the left of the blade.

If the desired cut-off length to the left of the blade is between 912" and 45", then the flip stop-end of the slide bar needs to be slid into the main miter fence body first (Figure 78).

Figure 76. Miter fence set to 45˚ mark on the

miter fence scale.

3.Loosen the lock knobs that secure the flip stop slide into position in the miter fence (Figure 77).

Lock Knobs

Miter Fence

Flip Stop

Figure 77. Flip stop slide lock knobs.

Figure 78. Miter fence slide installation for cut

lengths between 912" and 45".

If the desired cut-off length to the left of the blade is between 45" and 8612, then the slide bar end opposite the flip stop needs to be slid into the main miter fence body first (Figure 79).

Figure 79. Miter fence slide installation for cut

lengths between 45" and 8612.

G0501 Sliding Table Saw

-45-

Image 47
Contents Sliding Table SAW Page Table Of Contents Maintenance Safety Instructions for Power Tools Safety25ft 50ft 100ft Length AMP RatingAdditional Safety Instructions for Table Saws Below are tips to reduce the likelihood of kick- back Preventing KickbackProtecting Yourself From Kickback Glossary Of Terms Commentary General InformationCircuit Requirements 220V 3-PhaseTypical locking type L15-20 plug Receptacle 440V 3-PhaseGrounding Extension Cords To rewire the Model G0501 for 440V opera- tion Rewiring toMain Features Features & ControlsBlades Control Panel Blade Guard Controls Fence Assembly Lock Down LeverLeveling Adjustment Locking Lever Rip Fence ControlsMain Crate SET UPAbout this Section Piece Inventory UnpackingSaw unit Crosscut fence components Hardware Recognition Chart Working Clearances Clean Up Site ConsiderationsMoving & Placing Saw Base Unit Control panel correctly set up Table InstallationTo install the sliding table Access panel removed one side Shown To install the blade guard Installing Blade GuardTo install the extension tables Installing Extension TablesLarge extension table installed G0501 Sliding Table Saw Rip Fence To install the rip fenceTo assemble the crosscut table Crosscut TableMounting Shaft Miter Fence To install the miter fenceTest Run To adjust the sliding table parallel with the main blade Sliding Table Parallel AdjustmentTo align the fence scale with the blade Fence Scale AlignmentTo connect the dust ports to a dust collection system Dust CollectionPlease follow these tips Every time you use your saw OperationsOperation Tips To change the blade tilt Changing Blade TiltChanging Blade Speeds To align the scoring blade set Aligning Scoring Blade SetRip cutting with the sliding table Rip CuttingRip fence set even with center Blade G0501 Sliding Table Saw Rip cutting using the traditional table saw techniqueCrosscutting Crosscutting smaller panels Crosscutting using the rip fence as a cut-off gaugeCrosscutting full size panels Miter Cutting Mount the miter fence onto the sliding table To perform a miter cutTo change main blade Changing Main BladeTo change the riving knife Changing Riving KnivesTo change scoring blade set Changing Scoring Blade SetPage Belts MaintenanceCleaning MiscellaneousDate Approximate Hours Of Use Maintenance Performed Maintenance LogTo change the V-belt on the main motor Service AdjustmentsAbout Service Replacing BeltsTo calibrate the blade tilt Calibrating Blade TiltTo change the belt on the scoring blade motor To align the riving knife Adjusting Riving Knife AlignmentRepeat steps Squaring Crosscut Fence to BladeTo square the crosscut fence with the blade Reference Info Aftermarket AccessoriesReplacement Blades Machine Data Sheet Scoring Motor Sliding Table SAW Capacities G0501 Machine Frame Assembly G0501 Machine Frame/Saw Angle Measurement Assemblies G0501 Saw Angle Measurement AssemblyG0501 G0501 Chip Channel Assembly G0501 Saw Blade Adjustment Assembly PSB64M G0501 Main Saw Assemblies Bracket G0501 Scoring Saw Assemblies Description G0501 Swinging Arm Assembly Cleaning Brush 3LIDINGD4ABLEBANDN-ITERT&ENCEN!SSEMBLIES %&HaYc\IVWaZHVl G0501 Crosscut Table Square Plug G0501 Crosscut Fence Helical Pressure Spring G0501 Machine Table Assemblies Extension Table G0501 Rip Fence Assembly TOP Section G0501 Blade Guard Assembly Support ARM G0501 Electrical Panel Components Digital Control Display DP-525 Symptom Possible Cause Possible Solution Motor TroubleshootingPerformance Troubleshooting G0501 Control Panel Back Side Diagram G0501 Electrical Panel Warranty and Returns Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog