Grizzly G0501 instruction manual Service Adjustments, About Service, Replacing Belts

Page 54

SECTION 8: SERVICE ADJUSTMENTS

Always disconnect power to the machine before performing ser- vice adjustments. Failure to do this may result in serious personal injury.

About Service

This section is designed to help the operator with adjustments that were made at the factory and that might also need to be made during the life of the machine.

This section is provided for your convenience—it is not a substitute for the Grizzly Service Department. If any adjustments arise that are not described in this manual, then feel free to call the Grizzly Service Department at (570) 546-9663.

Similarly, if you are unsure of how to perform any procedure in this section, the Grizzly Service Department will be happy to guide you through the procedures or help in any other way.

Replacing Belts

To change the V-belt on the main motor:

1.Move the blade tilt to 0˚ on the control panel (blade 90˚ to table), and raise the main blade and scoring blade set up as far as they will go.

2.Disconnect the saw from the power source!

3.Open the motor cabinet door.

4.Move the belt tension handle (Figure 90) down to loosen the V-belt.

Figure 90. Belt tension handle.

5.Remove the old V-belt and replace it with a new belt.

6.Move the belt tension handle up to tighten the V-belt.

7.Close and secure the motor cabinet door.

-52-	G0501 Sliding Table Saw

Image 54

Contents Sliding Table SAW Page Table Of Contents Maintenance Safety Safety Instructions for Power ToolsLength AMP Rating 25ft 50ft 100ftAdditional Safety Instructions for Table Saws Preventing Kickback Protecting Yourself From KickbackBelow are tips to reduce the likelihood of kick- back Glossary Of Terms General Information Commentary220V 3-Phase Circuit Requirements440V 3-Phase Typical locking type L15-20 plug ReceptacleGrounding Extension Cords Rewiring to To rewire the Model G0501 for 440V opera- tionFeatures & Controls Main FeaturesBlades Control Panel Rip Fence Controls Fence Assembly Lock Down LeverLeveling Adjustment Locking Lever Blade Guard ControlsUnpacking SET UPAbout this Section Piece Inventory Main CrateSaw unit Crosscut fence components Hardware Recognition Chart Clean Up Site Considerations Working ClearancesMoving & Placing Saw Base Unit Table Installation Control panel correctly set upTo install the sliding table Access panel removed one side Shown Installing Blade Guard To install the blade guardInstalling Extension Tables To install the extension tablesLarge extension table installed G0501 Sliding Table Saw To install the rip fence Rip FenceCrosscut Table To assemble the crosscut tableMounting Shaft To install the miter fence Miter FenceTest Run Sliding Table Parallel Adjustment To adjust the sliding table parallel with the main bladeFence Scale Alignment To align the fence scale with the bladeDust Collection To connect the dust ports to a dust collection systemOperations Operation TipsPlease follow these tips Every time you use your saw Changing Blade Tilt Changing Blade SpeedsTo change the blade tilt Aligning Scoring Blade Set To align the scoring blade setRip Cutting Rip cutting with the sliding tableRip cutting using the traditional table saw technique Rip fence set even with center Blade G0501 Sliding Table SawCrosscutting Crosscutting using the rip fence as a cut-off gauge Crosscutting full size panelsCrosscutting smaller panels Miter Cutting To perform a miter cut Mount the miter fence onto the sliding tableChanging Main Blade To change main bladeChanging Riving Knives To change the riving knifeChanging Scoring Blade Set To change scoring blade setPage Miscellaneous MaintenanceCleaning BeltsMaintenance Log Date Approximate Hours Of Use Maintenance PerformedReplacing Belts Service AdjustmentsAbout Service To change the V-belt on the main motorCalibrating Blade Tilt To change the belt on the scoring blade motorTo calibrate the blade tilt Adjusting Riving Knife Alignment To align the riving knifeSquaring Crosscut Fence to Blade To square the crosscut fence with the bladeRepeat steps Aftermarket Accessories Replacement BladesReference Info Machine Data Sheet Scoring Motor Sliding Table SAW Capacities G0501 Machine Frame Assembly G0501 Saw Angle Measurement Assembly G0501 Machine Frame/Saw Angle Measurement AssembliesG0501 G0501 Chip Channel Assembly G0501 Saw Blade Adjustment Assembly PSB64M G0501 Main Saw Assemblies Bracket G0501 Scoring Saw Assemblies Description G0501 Swinging Arm Assembly Cleaning Brush 3LIDINGD4ABLEBANDN-ITERT&ENCEN!SSEMBLIES %&HaYc\IVWaZHVl G0501 Crosscut Table Square Plug G0501 Crosscut Fence Helical Pressure Spring G0501 Machine Table Assemblies Extension Table G0501 Rip Fence Assembly TOP Section G0501 Blade Guard Assembly Support ARM G0501 Electrical Panel Components Digital Control Display DP-525 Motor Troubleshooting Symptom Possible Cause Possible SolutionPerformance Troubleshooting G0501 Control Panel Back Side Diagram G0501 Electrical Panel Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC BOX BELLINGHAM, WAPage Call Today For a Free Full Color Catalog