RIDGID 690 manual Threading with 11-R Die Head, Installing No -R Die Heads

Page 8

No. 690 Portable Power Drive

Threading with 11-R Die Head

1.For 11/2- 211-R Die Heads, push die heads, spline

end first, squarely into the Power Drive until the spring engages securely (Figure 3). For 1/8- 11/411-R Die Heads, push die heads into adapter spline end first, until spring engages in notches.

NOTE! Installation can be made from only one side of the Power Drive.

Figure 3 – Installing No. 11-R Die Heads

2.If possible, secure the pipe in a portable tristand vise or a bench vise.

WARNING To prevent tipping, long lengths of pipe should also be supported with pipe stand.

3.Be sure the 418 Oiler is properly filled with RIDGID Thread Cutting Oil. Position the oiler in front of the vise.

4.Position No. 691 Support Arm on pipe so end of support arm is in line with end of the pipe (Figures 4 & 5). Make sure jaws squarely contact pipe and tighten handle firmly to prevent slipping of the jaws.

WARNING To avoid serious injury from losing control of the Power Drive, a support arm should be used when threading 3/4or larger pipe.

When threading pipe less than 3/4in size without a sup- port arm, hold onto the Power Drive firmly with one hand to exert pressure against the handle forces developed dur- ing threading.

Support Arm

Figure 4 – Using No. 691 Support Arm When Threading 3/4Pipe and Larger

Pipe

Support Arm

Figure 5 – Positioning No. 691 Support Arm In Line with End of Pipe

5.Position the directional switch for the desired right or left hand thread (Figure 6).

CAUTION Change position of the directional switch only when the motor is switched OFF.

CLOCKWISE

 

 

 

 

 

 

 

 

 

 

COUNTER-

 

 

 

 

 

 

 

 

 

 

 

CLOCKWISE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A. Right Hand Thread ON

B. Left Hand Thread ON

COUNTER-

CLOCKWISE

 

 

 

 

 

 

 

CLOCKWISE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A. Right Hand Thread OFF

B. Left Hand Thread OFF

Figure 6 – Direction Change Switch/Die Head Orientation

6

Ridge Tool Company

Image 8
Contents Portable Power Drive Table of Contents 690 Portable Power Drive General Safety Information Work Area SafetyElectrical Safety Personal SafetySpecific Safety Information Description, Specifications and Standard EquipmentPower Drive Inspection AccessoriesOperating Instructions For Threading with 11-R Die Heads Installation of AdapterTool and Work Area Set-Up Installing No -R Die Heads Threading with 11-R Die HeadMaintenance Instructions AccessoriesMotor Brush Replacement Accessories For Power DriveService and Repair Troubleshooting Problem Cause CorrectionWiring Diagram FOR/REVSystème d’entraînement portatif n Table des matières Consignes générales de sécuritéConsignes générales de sécurité Sécurité du chantierSécurité électrique Sécurité individuelleService après-vente Consignes de sécurité particulièresUtilisation et entretien de l’appareil Sécurité du système d’entraînementSpécifications et équipements de base AccessoiresDescription, spécifications et équipements de base Inspection du système d’entraînement Préparation de l’appareil et du chantierLe filetage avec les têtes de filière type 11-R Le filetage avec têtes de filière 11-RMontage de l’adaptateur Inverseur/ Orientation des têtes de filière Accessoires Service après-vente et réparationsEntretien Stockage de l’appareilProbleme Raisons Possibles DépannageSchéma électrique Système d’entraînement portatif n Accionamiento Motorizado portátil No Índice Información general de seguridadInformación general de seguridad Seguridad en la zona de trabajoSeguridad eléctrica Seguridad personalInformación específica de seguridad Uso y cuidado de la máquinaServicio Seguridad del Accionamiento MotorizadoDescripción, especificaciones y equipo estándar DescripciónEspecificaciones y equipo estándar AccesoriosInspección del Accionamiento Motorizado Preparación de la máquina y de la zona de trabajoInstalación del adaptador Roscado con un cabezal de terrajas 11-RFigura 7 Aplicación de aceite mientras se rosca Instrucciones para el mantenimiento AccesoriosAlmacenamiento de la máquina Recambio de las escobillas del motorServicio y reparaciones Problema Causa Remedio Detección de averíasDiagrama de cableado ON/OFFRidge Tool Company