RIDGID hc-450, hc-300 manual Inspect Hole Cutting Tool, Set-Up Instructions, Model HC-450

Page 7

HC-450/HC-300 Hole Cutting Tools

B

Figure 2 – Dimension B

Figure 3 – HC-450 with Standard Equipment

Inspect Hole Cutting Tool

WARNING

To prevent serious injury, inspect your Hole Cutting Tool on a regular basis. The following inspection procedures should be performed before each use of the tool:

1.Inspect the power cord and plug for damage. If the grounding prong is missing or the cord or GFCI is damaged, do not use the tool until the cord has been replaced.

2.Make sure the switches turn the tool ON and OFF. If broken, do not use until they are replaced.

3.Inspect the power drive for any broken, missing, misaligned, or binding parts as well as any condi- tions, which may affect the safe and normal opera- tion of the tool. If any of these conditions are

present, do not use the tool until the problem has been repaired. Do not use dull, bent, or damaged hole saws or arbors.

4.Test the Ground Fault Circuit Interrupter (GFCI) to insure it is operating correctly. When test button is pushed in, the indicator light should go OFF. Reactivate by pushing the reset button in. If the indi- cator light goes ON, the tool is ready to use. If bro- ken, do not use the tool until it is replaced.

5.Clean any oil, grease, or dirt from the handles. This reduces the risk of injury due to the tool slip- ping from your grip.

6.Use only accessories recommended for your tool. Accessories used for other tools may be haz- ardous when used on a hole saw and lead to seri- ous injury.

7.Inspect the cutting edges of your hole saws. If nec- essary, replace prior to using in your hole-cutting tool. Dull or damaged cutting edges can lead to injury, tool breakage, or excessive heat buildup in the workpiece and the tool.

Set-Up Instructions

Model HC-450

WARNING

When setting up the hole saw, it should be unplugged and the switch should be in the OFF position. To prevent serious injury the tool must be properly set up.

1.Determine the size and location of hole to be cut. Follow coupling manufacturer’s recommendations for hole size to coupling size.

2.Select hole saw and arbor to correct hole size. Integral arbor hole saws are recommended to reduce chatter. See Table 1 for ordering information.

Hole Saw Ordering Information – Table #1

Hole Diameter

Hole

Arbor

Integral

Saw

Cat.

Saw

 

 

Inches

mm

Cat. No.

No.

w/Arbor

2

51

52865

53080

56902

21/2

64

52895

53080

56907

23/4

70

52910

53080

56912

31/2

89

52940

59502

56917

41/2

114

52980

59502

56922

NOTE! 53080 Arbor is 5/8Hex; requires 5/8Chuck. 59502 Arbor and backing plate is for hole saws larger than 3.

Ridge Tool Company • Elyria, Ohio • U.S.A.

5

Image 7
Contents HC-300 Table of Contents HC-450/HC-300 Hole Cutting Tools Personal Safety General Safety InformationWork Area Safety Electrical SafetyService Specific Safety InformationTool Use and Care Model HC-450 Description, Specifications and Accessories Set-Up Instructions Inspect Hole Cutting ToolModel HC-450 Mount unit in the proximity to hole location HC-450 on a Horizontal Cut Operating InstructionsLocating Level Vial Instructions Model HC-300 Description, Specifications and AccessoriesModel HC-300 Model HC-300 Plunger Tightening Chain Model HC-300 ON/OFF Switch Service and Repair MaintenanceMotor Brush Replacement HC-450/HC-300 Hole Cutting Tools Scies à cloche HC-450/300 Consignes générales de sécurité Table des matièresSécurité du chantier Consignes générales de sécuritéSécurité électrique Utilisation et entretien de l’appareil Sécurité personnelleRéparations Consignes de Sécurité Particulières Modèle HC-450 Description, spécifications et accessoiresSécurité de l’appareil Equipements de base AccessoiresExamen de la scie à cloche SpécificationsModèle HC-450 Installation de l’appareilInstallez l’appareil à proximité de l’emplacement du trou Utilisation du niveau de posi- tionnement Mode d’emploiNiveau à bulle du modèle HC-450 Modèle HC-300 Description, spécifications et accessoiresModèle HC-300 Plongeur du modèle HC-300 Surface de montage de niveau de la HC-300 Interrupteur marche/arrête du modèle HC-300 Entretien Remplacement des balais du moteurEntretien et réparations Scies à cloche HC-450 HC-300 Máquinas Perforadoras HC-450/HC-300 Información general de seguridad IndiceSeguridad en la zona de trabajo Información general de seguridadSeguridad eléctrica Uso y cuidado de la herramienta Seguridad personalServicio Seguridad en el uso de la herramienta Información específica de seguridadDescripción Equipo estándar EspecificacionesAccesorios Instrucciones para la instalación Revisión de la perforadoraModelo HC-450 Monte la unidad próxima al lugar donde perforará el agujero Figura 7 La HC-450 haciendo un corte horizontal Instrucciones para el funcionamientoDescripción, especificaciones y accesorios del Modelo HC-300 Instrucciones para situar el tubito de nivelaciónModelo HC-300 Figura 13 Pistón del Modelo HC-300 Figura 18 Zona para la nivelación del Modelo HC-300 Figura 20 Interruptor de ON/OFF en el Modelo HC-300 Servicio y reparaciones MantenimientoRecambio del cepillo del motor Máquinas Perforadoras HC-450/HC-300 Lifetime Warranty