Sears 137.28463 operating instructions Riving Knife Assembly

Page 24

2.Removethearbornut(2)andouter bladeflange(3).(Fig.T)

RIVING KNIFE ASSEMBLY

l_ WARNING l

3.Placethebladeontothearbor(4) withthebladeteethpointingforward tothefrontofthesaw.(Fig.U) NOTE:Leavetheplasticstriparound thesawbladeatthistime.Remove

beforeusingthesawforthefirst time.

4.Makesurethebladefitsflush againsttheinnerflange.

5.Cleantheouterbladeflange(3) andinstallit ontothearbor(4)and againsttheblade.(Fig.T)

6.Threadthearbornut(2)ontothe

arbor,makingsuretheflatsideof

thenutisagainsttheblade,then hand-tighten(Fig. .T)

7.Totightenthearbornut(2),place theopen-endwrench(6)onthe flatsofthesawarbor(5)tokeepthe arborfromturning.(Fig.U)

8.Placethebox-endwrench(7)onthe arbornut(2)andturnclockwise(to therearofthesawtable).(Fig.U)

9.Donotreplaceinsertuntilafterthe nextstepofaddingtherivingknife assembly.

>/

e To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug

is disconnected from the power source outlet.

eNever operate this saw without the riving knife in the correct position.

installing the riving knife assembly (Fig. V, W, W=I)

NOTE: The table insert should be removed and the blade raised to its

highest position before proceeding.

1.Loosen the blade lock handle (1).

Turn and move the handwheel (2) to 45° on the bevel scale.

2.Tighten the bevel lock handle.

Fig. V

21

3.Place the riving knife (3) on the mounting bracket (4) located behind

the saw blade. The two pins (5) on the bracket should fit into the slot on

the riving knife.

4.Make sure the riving knife (3) is in its highest position.

5.Insert the set plate (6) making sure the two outer holes fit into the two

pins on the mounting bracket.

6.Insert the washer (7) into the lock lever (8) and insert into the middle hole the set plate and tighten.

7.Loosen the blade lock handle (1) and return the blade to 0° and lock.

8.Place the table insert back into position.

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Operators Manual Section Motor Blade SizeSAW PROHiBiTiON Support and Clamp WorkGeneralsafety iNSTRUCTiONS Wear Proper ApparelSecure Page Alwaysusesawblade Page Kickbacks Power Supply and Motor SPECiFiCATiONS Grounding iNSTRUCTiONSImmediately La, Caution Recommended Accessories 308K Dado Insert PlateSupplied not Supplied Obtained and is installed correctly Loose Parts SAW Description QuantityStand ACD EFG H KLM STUStand lock hook Page Overload Reset Switch Revolutions PER Minute RPMOrder to Avoid iNJURY Do not release the stand hooksSetting UP the Stand Fig. DInstalling the Blade Guard ANTI-KICKBACK PawlsInstalling the Power Cord Storage Clamps Fig. NAssembling the Blade ELEVATION/TILT HandwheelInstalling the Rear Table Fig. QRiving Knife Assembly Fig. W Blade Guard Assembly Adjustments Fig. YAnti=kickback pawl assembly Fig. Z, AA, BB Additional BladeFig. Z Improper riving knife alignment can Fig. DDRiP Fence Adjustment Fig. FF Adjusting the Miter GaugeAdjusting the Table iNSERT Fig. JJ-1 BLADETiLTiNG Scale iNDiCATOR Power source when making any adjustmentsTo prevent personal injury ON/OFF Switch Fig. NN Basic SAW OperationsTilting the Blade Cutting Operations Never USE the TWO AT the Same TimeTurnthesawONandwaitforthe bladetocometofullspeed Ripping Small Pieces Helpful DevicesAuxiliary Fence Fig. TT Push BlockMake a Push Block Fig. UU Making the base To prevent serious injury Fig. WWCompound Miter Crosscutting MiTERiNG Fig. ZZ00~45 Miter Angle Fig. bb NON-THROUGHDo not use Adjustable or Wobble type dadoes For your own safety, always replaceDADOCUTSFIG. cc, dd Maintaining Your Table SAW General Maintenance Blade Raising and TiltingMechanism Fig. ee, ff Clean the Blade Tilting Scale Indicator LUBRiCATiONReplacing the Carbon Problem Possible Causes CorrectiveAction Tilting Cut Here To WAR.I.Gi Schematic a 10 iN. Jobsite Table SAW Model NO= 137=284630Parts LiST for Motor 10 iN, JobsiteTable SAW Model noParts LiST for Stand 10 IN. Jobsite Table SAWSears Installation Service ServiceOurHome Wv sears,tom Wvvv.sears.ca
Top Page Image Contents