Sears 137.28463 operating instructions Fig. W

Page 25

i_ WARNING ]

oTo avoid the lock lever interferring the table insert, after tighten the riving knife, position the lock lever pointing downward before using saw. Failure to maintain a level insert can result in serious injury to the operator.

oThe lever can be pulled out to allow it to be turned to a new position downward. (Fig. W-1)

Fig. W

J

Fig. W-1

Aligning the riving knife (Fig. X)

[_ WARNING]

o To avoid injury from an accidental start, make sure the switch is in

the OFF position and the plug

is disconnected from the power source outlet.

o Never operate this tool without the riving knife in the correct position.

oNever operate this tool without the blade guard in place for all through sawing operations.

o This adjustment was made at the factory, but it should be rechecked and adjusted if necessary.

1.Remove the table insert and raise the blade to the maximum height by turning the blade elevation handwheel clockwise.

2.Remove the blade guard and anti- kickback pawl assembly.

3.Adjust the blade to the 0° vertical position by unlocking the blade tilting lock knob and turning the bevel tilting handwheel counterclockwise, and then lock into position.

4.To see if the blade (1) and riving knife (2) are correctly aligned, lay a combination square along the side of the blade and against the riving knife (making sure the square is between the teeth of the blade).

5.Tilt the blade to the 45° position and check the alignment again.

NOTE:

oThis table saw is provided with a 10 inch diameter blade with a body thickness of 0.07 in. (1.8 mm) thick

with a kerf of 0.10 in. (2.6 mm ).The riving knife is 0.09 in. (2.2 mm) thick.The blade diameter and the

blade body and kerf dimensions must be properly matched with the riving knife thickness.

o The maximum radial distance

between the riving knife and the toothed rim of the saw blade is 0.12

in - 0.31 in. (3 mm - 8 mm)

oThe tip of the riving knife shall not be lower than 0.04 in. _ 0.2 in. (1 mm _ 5 mm) from the tooth peak.

oThe riving knife is thinner than the width of the kerf by approximately 1/64 in. (0.4 mm) on each side.

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Operators Manual Section Blade Size MotorSAW Support and Clamp Work PROHiBiTiONWear Proper Apparel Generalsafety iNSTRUCTiONSSecure Page Alwaysusesawblade Page Kickbacks Grounding iNSTRUCTiONS Power Supply and Motor SPECiFiCATiONSImmediately La, Caution 308K Dado Insert Plate Recommended AccessoriesSupplied not Supplied Loose Parts SAW Description Quantity Obtained and is installed correctlyStand STU ACD EFG H KLMStand lock hook Page Revolutions PER Minute RPM Overload Reset SwitchDo not release the stand hooks Order to Avoid iNJURYFig. D Setting UP the StandANTI-KICKBACK Pawls Installing the Blade GuardStorage Clamps Fig. N Installing the Power CordAssembling the Blade ELEVATION/TILT HandwheelFig. Q Installing the Rear TableRiving Knife Assembly Fig. W Adjustments Fig. Y Blade Guard AssemblyAnti=kickback pawl assembly Fig. Z, AA, BB Additional BladeFig. Z Fig. DD Improper riving knife alignment canAdjusting the Miter Gauge RiP Fence Adjustment Fig. FFAdjusting the Table iNSERT Fig. JJ-1 Power source when making any adjustments BLADETiLTiNG Scale iNDiCATORTo prevent personal injury Basic SAW Operations ON/OFF Switch Fig. NNTilting the Blade Never USE the TWO AT the Same Time Cutting OperationsTurnthesawONandwaitforthe bladetocometofullspeed Helpful Devices Ripping Small PiecesPush Block Auxiliary Fence Fig. TTMake a Push Block Fig. UU Making the base Fig. WW To prevent serious injuryMiTERiNG Fig. ZZ Compound Miter Crosscutting00~45 Miter Angle NON-THROUGH Fig. bbFor your own safety, always replace Do not use Adjustable or Wobble type dadoesDADOCUTSFIG. cc, dd Blade Raising and Tilting Maintaining Your Table SAW General MaintenanceMechanism Fig. ee, ff LUBRiCATiON Clean the Blade Tilting Scale IndicatorReplacing the Carbon Causes Corrective Problem PossibleAction Tilting Cut Here To WAR.I.Gi 10 iN. Jobsite Table SAW Model NO= 137=284630 Schematic a10 iN, Jobsite Parts LiST for MotorTable SAW Model no10 IN. Jobsite Table SAW Parts LiST for StandService Sears Installation ServiceWv sears,tom Wvvv.sears.ca OurHome
Top Page Image Contents