Sears 137.28463 operating instructions Installing the Rear Table, Fig. Q

Page 23

INSTALLING THE REAR TABLE

EXTENSION (Fig. Q, R)

1.Insert the two tubes (2) into the rear table extension (1). (Fig. Q)

NOTE: They must be inserted into the back of the extension with the bent end last so that the bar will hold the

extension in place. The two openings on the rear table (4) must line up with the miter gauge slots on the main table.

2.Snap plastic stops (3) over the two rear table extension tubes (2). Make sure the locating pin in the black plastic stops fits into the matching hole in the extension tube. This will 'lock'the tube into the extension. (Fig. Q)

3.Insert the rear table extension tubes

(2)into the two extension tube brackets under the table (5).

Fig. Q

Bent End

/

\

\

Fig. R

INSTALLING THE BLADE (Fig. S, T, U)

i_ WARNING]

To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is not connected to the power source outlet.

. Remove the table insert (1) by snapping out from the hole (8). Raise the blade arbor to the

maximum height by turning the blade elevation handwheel

clockwise. (Fig. S)

Fig. S

4.Thread the screw (6) through the hole in either side tube with a

screwdriver. NOTE: Only one side is needed to have a screw inserted.

Tighten with a screwdriver, making sure not to overtighten the screw (6). (Fig. R)

Image 23

Contents Operators Manual Section SAW MotorBlade Size Support and Clamp Work PROHiBiTiONWear Proper Apparel Generalsafety iNSTRUCTiONSSecure Page Alwaysusesawblade Page Kickbacks Immediately Power Supply and Motor SPECiFiCATiONSGrounding iNSTRUCTiONS La, Caution Supplied not Supplied Recommended Accessories308K Dado Insert Plate Stand Obtained and is installed correctlyLoose Parts SAW Description Quantity STU ACD EFG H KLMStand lock hook Page Revolutions PER Minute RPM Overload Reset SwitchDo not release the stand hooks Order to Avoid iNJURY Fig. D Setting UP the StandANTI-KICKBACK Pawls Installing the Blade GuardELEVATION/TILT Handwheel Installing the Power CordStorage Clamps Fig. N Assembling the BladeFig. Q Installing the Rear TableRiving Knife Assembly Fig. W Additional Blade Blade Guard AssemblyAdjustments Fig. Y Anti=kickback pawl assembly Fig. Z, AA, BBFig. Z Fig. DD Improper riving knife alignment canAdjusting the Miter Gauge RiP Fence Adjustment Fig. FFAdjusting the Table iNSERT Fig. JJ-1 To prevent personal injury BLADETiLTiNG Scale iNDiCATORPower source when making any adjustments Tilting the Blade ON/OFF Switch Fig. NNBasic SAW Operations Never USE the TWO AT the Same Time Cutting OperationsTurnthesawONandwaitforthe bladetocometofullspeed Helpful Devices Ripping Small PiecesMake a Push Block Fig. UU Making the base Auxiliary Fence Fig. TTPush Block Fig. WW To prevent serious injury00~45 Miter Angle Compound Miter CrosscuttingMiTERiNG Fig. ZZ NON-THROUGH Fig. bbDADOCUTSFIG. cc, dd Do not use Adjustable or Wobble type dadoesFor your own safety, always replace Mechanism Fig. ee, ff Maintaining Your Table SAW General MaintenanceBlade Raising and Tilting Replacing the Carbon Clean the Blade Tilting Scale IndicatorLUBRiCATiON Action Problem PossibleCauses Corrective Tilting Cut Here To WAR.I.Gi 10 iN. Jobsite Table SAW Model NO= 137=284630 Schematic aModel no Parts LiST for Motor10 iN, Jobsite Table SAW10 IN. Jobsite Table SAW Parts LiST for StandService Sears Installation ServiceWv sears,tom Wvvv.sears.ca OurHome