Sears 137.28463 operating instructions Ripping Small Pieces, Helpful Devices

Page 36

BEVELRIPPING Thiscutisthesameasrippingexcept thebladebevelangleissettoanangle otherthan"0°''.

RIPPING SMALL PIECES

To avoid injury from the blade contact, never make cuts narrower than 3/4 in. wide.

1.It is unsafe to rip small pieces. Instead, rip a larger piece to obtain the size of the desired piece.

2.When a small width is to be ripped, your hand cannot be safely put between the blade and the rip fence, use push stick or push block to pass the workpiece completely through and past the blade.

HELPFUL DEVICES

In order to make some of cuts, it is necessary to use the devices like, push block, featherboard and auxiliary fence, which you can make yourself. Here are some templates for your reference.

FEATHERBOARD (FIG. RR, SS) A featherboard is a device used to help control the workpiece by guiding it securely against the table or fence. Featherboards are especially useful when ripping small workpieces and for completing non-through cuts. The end is angled with a number of short kerfs to give a friction hold on the workpiece and locked in place on the table

with C-clamps. Test that it can resist kickback.

[_ WARNING ]

Place the featherboard against the uncut portion of the workpiece to avoid kickback that could cause serious personal injury.

MAKE A FEATHERBOARD (Fig. RR) Select a solid piece of lumber approximately 3/4 in thick, 4 in wide and 18 in long. To make a featherboard, cut one end of the lumber at 60 degrees, then cut 8 in-long slots 1/4 in apart on the angled end as shown in Fig. RR.

Fig. RR

_-I

	, , r £	"i
_l	I.	8in -I

-'	18 in	_l

USE A FEATHERBOARD (Fig. SS)

1.Lower the saw blade (1).

2.Position the rip fence (2) to the desired adjustment and lock the rip fence.

3.Place the workpiece (3) against the fence and over the saw blade area.

4.Adjust the featherboard (4) to resist the workpiece forward of the blade.

5.Attached the C-clamps (5) to secure the featherboard to the edge of the table.

Fig. SS

5

\

Image 36

Contents Operators Manual Section Motor Blade SizeSAW PROHiBiTiON Support and Clamp WorkGeneralsafety iNSTRUCTiONS Wear Proper ApparelSecure Page Alwaysusesawblade Page Kickbacks Power Supply and Motor SPECiFiCATiONS Grounding iNSTRUCTiONSImmediately La, Caution Recommended Accessories 308K Dado Insert PlateSupplied not Supplied Obtained and is installed correctly Loose Parts SAW Description QuantityStand ACD EFG H KLM STUStand lock hook Page Overload Reset Switch Revolutions PER Minute RPMOrder to Avoid iNJURY Do not release the stand hooksSetting UP the Stand Fig. DInstalling the Blade Guard ANTI-KICKBACK PawlsInstalling the Power Cord Storage Clamps Fig. NAssembling the Blade ELEVATION/TILT HandwheelInstalling the Rear Table Fig. QRiving Knife Assembly Fig. W Blade Guard Assembly Adjustments Fig. YAnti=kickback pawl assembly Fig. Z, AA, BB Additional BladeFig. Z Improper riving knife alignment can Fig. DDRiP Fence Adjustment Fig. FF Adjusting the Miter GaugeAdjusting the Table iNSERT Fig. JJ-1 BLADETiLTiNG Scale iNDiCATOR Power source when making any adjustmentsTo prevent personal injury ON/OFF Switch Fig. NN Basic SAW OperationsTilting the Blade Cutting Operations Never USE the TWO AT the Same TimeTurnthesawONandwaitforthe bladetocometofullspeed Ripping Small Pieces Helpful DevicesAuxiliary Fence Fig. TT Push BlockMake a Push Block Fig. UU Making the base To prevent serious injury Fig. WWCompound Miter Crosscutting MiTERiNG Fig. ZZ00~45 Miter Angle Fig. bb NON-THROUGHDo not use Adjustable or Wobble type dadoes For your own safety, always replaceDADOCUTSFIG. cc, dd Maintaining Your Table SAW General Maintenance Blade Raising and TiltingMechanism Fig. ee, ff Clean the Blade Tilting Scale Indicator LUBRiCATiONReplacing the Carbon Problem Possible Causes CorrectiveAction Tilting Cut Here To WAR.I.Gi Schematic a 10 iN. Jobsite Table SAW Model NO= 137=284630Parts LiST for Motor 10 iN, JobsiteTable SAW Model noParts LiST for Stand 10 IN. Jobsite Table SAWSears Installation Service ServiceOurHome Wv sears,tom Wvvv.sears.ca