Sears 137.28463 operating instructions Adjusting the Table iNSERT

Page 30

ADJUSTING THE TABLE iNSERT

(Fig. ii)

[,A WARNING]

To avoid serious injury, the table

insert (2) must be level with the table, if the table insert is not flush

with the table, adjust the two bolts

(1)with a 4 mm he× wrench until it is parallel with the table.

NOTE: To raise the insert, turn the hex screws counterclockwise. To lower the insert, turn the hex screws clockwise.

Do not remove the insert, adjustments need to be made with the insert in

place to get the proper level.

Fig. II

REMOVING THE BLADE (Fig. S, T, U)

I,,A WARNING]

To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is disconnected from the power source outlet.

1.Remove the table insert by snapping out from the hole (8). (Fig. S)

2.Raise the blade to the maximum

height by turning the blade elevation handwheel clockwise.

3.Adjust the blade to the 90 ° vertical position by unlocking the blade

tilting lock knob, push in the blade elevation wheel and turn the bevel

tilting handwheel counterclockwise, and then lock into position.

4.Place the box-end wrench (7) on the arbor nut (2). (Fig. U)

5.Place the open-end wrench (6) on the flats of the saw arbor to keep the arbor from turning and loosen the arbor nut (2). (Fig. U)

6.Then remove the blade. Clean but do not remove the inner blade flange before reassembling the blade.

Image 30

Contents Operators Manual Section Motor Blade SizeSAW PROHiBiTiON Support and Clamp WorkGeneralsafety iNSTRUCTiONS Wear Proper ApparelSecure Page Alwaysusesawblade Page Kickbacks Power Supply and Motor SPECiFiCATiONS Grounding iNSTRUCTiONSImmediately La, Caution Recommended Accessories 308K Dado Insert PlateSupplied not Supplied Obtained and is installed correctly Loose Parts SAW Description QuantityStand ACD EFG H KLM STUStand lock hook Page Overload Reset Switch Revolutions PER Minute RPMOrder to Avoid iNJURY Do not release the stand hooksSetting UP the Stand Fig. DInstalling the Blade Guard ANTI-KICKBACK PawlsAssembling the Blade Installing the Power CordStorage Clamps Fig. N ELEVATION/TILT HandwheelInstalling the Rear Table Fig. QRiving Knife Assembly Fig. W Anti=kickback pawl assembly Fig. Z, AA, BB Blade Guard AssemblyAdjustments Fig. Y Additional BladeFig. Z Improper riving knife alignment can Fig. DDRiP Fence Adjustment Fig. FF Adjusting the Miter GaugeAdjusting the Table iNSERT Fig. JJ-1 BLADETiLTiNG Scale iNDiCATOR Power source when making any adjustmentsTo prevent personal injury ON/OFF Switch Fig. NN Basic SAW OperationsTilting the Blade Cutting Operations Never USE the TWO AT the Same TimeTurnthesawONandwaitforthe bladetocometofullspeed Ripping Small Pieces Helpful DevicesAuxiliary Fence Fig. TT Push BlockMake a Push Block Fig. UU Making the base To prevent serious injury Fig. WWCompound Miter Crosscutting MiTERiNG Fig. ZZ00~45 Miter Angle Fig. bb NON-THROUGHDo not use Adjustable or Wobble type dadoes For your own safety, always replaceDADOCUTSFIG. cc, dd Maintaining Your Table SAW General Maintenance Blade Raising and TiltingMechanism Fig. ee, ff Clean the Blade Tilting Scale Indicator LUBRiCATiONReplacing the Carbon Problem Possible Causes CorrectiveAction Tilting Cut Here To WAR.I.Gi Schematic a 10 iN. Jobsite Table SAW Model NO= 137=284630Table SAW Parts LiST for Motor10 iN, Jobsite Model noParts LiST for Stand 10 IN. Jobsite Table SAWSears Installation Service ServiceOurHome Wv sears,tom Wvvv.sears.ca