Sears 137.28463 LUBRiCATiON, Replacing the Carbon, Clean the Blade Tilting Scale Indicator

Page 43

LUBRiCATiON

All motor bearings are permanently lubricated at the factory and require no additional lubrication. On all mechanical parts of your table saw where a pivot or threaded rod are present, lubricate using graphite or silicone. These dry lubricants will not hold sawdust as would oil or grease.

REPLACING THE CARBON

rip fence, miter gauge and stand assembly to the table saw.

NOTE: To reinstall the same brushes, first make sure the brushes go back in the same sides they came out. This will avoid a break-in period that reduces motor performance and increases wear.

Fig. gg

3

[_ WARNING]

Always disconnect the plug from the power source before inspecting the brushes.

The carbon brushes included with the unit will last approximately 50 hours of running time, or 10,000 ON/OFF cycles. Replace both carbon brushes when either has less than 1/4 in. length of carbon remaining, or if the spring or wire is damaged or burned.

1.Remove the blade guard, blade, rip fence, miter gauge and stand assembly from the table saw.

2.Lower the blade height to its minimum setting. This will make the brushes's location easier to access.

3.Place cardboard or an old blanket

on the floor to protect the saw table surface.

4.Place the saw upside down on the protective material.

5.Tilt the blade elevation/tilting handwheel (1) to the 45 ° position.

6.Remove the black plastic cap (2) from the side of the motor (3).

7.Carefully remove the spring-loaded cap, and then pull out the brush (4).

8.Repeat step 6 and 7 for the other side of motor.

9.Place the new brush into the

opening of motor, making sure the ears on the metal end of the

assembly go in the same hole the carbon part fits into. Do not overtighten the plastic cap.

10.Carefully set the saw in a upright position on a clean level surface.

11 .Replace the blade guard, blade,

Fig. hh

'\\

 

/

\

\

 

 

 

CLEAN THE BLADE TILTING SCALE INDICATOR

NOTE: Occasionally cleaning the blade tilting scale indicator to remove dust may be necessary as a result of normal use. (Also see Fig. KK on page 32)

1.Release two screws on the cover

set on the pointer. Clean the dust

accumulated in the pointer and inside of the cover.

2.Position the pointer to 0°.

3.Replace the cover and tighten the two screws.

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Operators Manual Section Blade Size MotorSAW Support and Clamp Work PROHiBiTiONWear Proper Apparel Generalsafety iNSTRUCTiONSSecure Page Alwaysusesawblade Page Kickbacks Grounding iNSTRUCTiONS Power Supply and Motor SPECiFiCATiONSImmediately La, Caution 308K Dado Insert Plate Recommended AccessoriesSupplied not Supplied Loose Parts SAW Description Quantity Obtained and is installed correctlyStand STU ACD EFG H KLMStand lock hook Page Revolutions PER Minute RPM Overload Reset SwitchDo not release the stand hooks Order to Avoid iNJURYFig. D Setting UP the StandANTI-KICKBACK Pawls Installing the Blade GuardELEVATION/TILT Handwheel Installing the Power CordStorage Clamps Fig. N Assembling the BladeFig. Q Installing the Rear TableRiving Knife Assembly Fig. W Additional Blade Blade Guard AssemblyAdjustments Fig. Y Anti=kickback pawl assembly Fig. Z, AA, BBFig. Z Fig. DD Improper riving knife alignment canAdjusting the Miter Gauge RiP Fence Adjustment Fig. FFAdjusting the Table iNSERT Fig. JJ-1 Power source when making any adjustments BLADETiLTiNG Scale iNDiCATORTo prevent personal injury Basic SAW Operations ON/OFF Switch Fig. NNTilting the Blade Never USE the TWO AT the Same Time Cutting OperationsTurnthesawONandwaitforthe bladetocometofullspeed Helpful Devices Ripping Small PiecesPush Block Auxiliary Fence Fig. TTMake a Push Block Fig. UU Making the base Fig. WW To prevent serious injuryMiTERiNG Fig. ZZ Compound Miter Crosscutting00~45 Miter Angle NON-THROUGH Fig. bbFor your own safety, always replace Do not use Adjustable or Wobble type dadoesDADOCUTSFIG. cc, dd Blade Raising and Tilting Maintaining Your Table SAW General MaintenanceMechanism Fig. ee, ff LUBRiCATiON Clean the Blade Tilting Scale IndicatorReplacing the Carbon Causes Corrective Problem PossibleAction Tilting Cut Here To WAR.I.Gi 10 iN. Jobsite Table SAW Model NO= 137=284630 Schematic aModel no Parts LiST for Motor10 iN, Jobsite Table SAW10 IN. Jobsite Table SAW Parts LiST for StandService Sears Installation ServiceWv sears,tom Wvvv.sears.ca OurHome
Top Page Image Contents