Sears 137.28463 operating instructions

Page 9

14.AVOIDAWKWARD OPERATIONS and hand positions where a sudden slip could cause your hand to move into the saw blade.

15.NEVER USE SOLVENTS to clean plastic parts. Solvents could possibly dissolve or otherwise damage the material. Only a soft damp cloth should be used to clean plastic parts.

16.MOUNT your table saw on a bench or stand before performing any cutting operations. Refer to ASSEMBLY on page 19.

17"1,A_ WARNING ]

Never cut metals or masonry products with this tool. This table saw is designed for use on wood and wood-like products only.

18.ALWAYS USE IN A WELL= VENTILATED AREA. Remove

sawdust frequently. Clean out sawdust from the interior of the saw

to prevent a potential fire hazard.

19.NEVER LEAVE THE SAW RUNNING UNATTENDED. Do not leave the saw until the blade comes to a complete stop.

20.For proper operation follow the instructions in this Instruction Manual entitled ASSEMBLY AND

ADJUSTMENTS (Page 19). Failure

to provide sawdust fall-through and removal hole will allow sawdust to

build up in the motor area resulting in a fire hazard and potential motor damage.

21 .USE ONLY saw blades recommended with the warning that the riving knife shall not be thicker than the width of the groove cut by the saw blade and not thinner than the body of the saw blade.

22.USE PUSH-STICK OR PUSH BLOCK to feed the workpiece past the saw blade. The push-stick or push block should always be stored with the machine when not in use.

23.DIRECTION OF FEED. Feed workpiece into a blade or cutter against the direction of rotation of the blade or cutter only.

Image 9

Contents Operators Manual Section Motor Blade SizeSAW Support and Clamp Work PROHiBiTiONWear Proper Apparel Generalsafety iNSTRUCTiONSSecure Page Alwaysusesawblade Page Kickbacks Power Supply and Motor SPECiFiCATiONS Grounding iNSTRUCTiONSImmediately La, Caution Recommended Accessories 308K Dado Insert PlateSupplied not Supplied Obtained and is installed correctly Loose Parts SAW Description QuantityStand STU ACD EFG H KLMStand lock hook Page Revolutions PER Minute RPM Overload Reset SwitchDo not release the stand hooks Order to Avoid iNJURYFig. D Setting UP the StandANTI-KICKBACK Pawls Installing the Blade GuardStorage Clamps Fig. N Installing the Power CordAssembling the Blade ELEVATION/TILT HandwheelFig. Q Installing the Rear TableRiving Knife Assembly Fig. W Adjustments Fig. Y Blade Guard AssemblyAnti=kickback pawl assembly Fig. Z, AA, BB Additional BladeFig. Z Fig. DD Improper riving knife alignment canAdjusting the Miter Gauge RiP Fence Adjustment Fig. FFAdjusting the Table iNSERT Fig. JJ-1 BLADETiLTiNG Scale iNDiCATOR Power source when making any adjustmentsTo prevent personal injury ON/OFF Switch Fig. NN Basic SAW OperationsTilting the Blade Never USE the TWO AT the Same Time Cutting OperationsTurnthesawONandwaitforthe bladetocometofullspeed Helpful Devices Ripping Small PiecesAuxiliary Fence Fig. TT Push BlockMake a Push Block Fig. UU Making the base Fig. WW To prevent serious injuryCompound Miter Crosscutting MiTERiNG Fig. ZZ00~45 Miter Angle NON-THROUGH Fig. bbDo not use Adjustable or Wobble type dadoes For your own safety, always replaceDADOCUTSFIG. cc, dd Maintaining Your Table SAW General Maintenance Blade Raising and TiltingMechanism Fig. ee, ff Clean the Blade Tilting Scale Indicator LUBRiCATiONReplacing the Carbon Problem Possible Causes CorrectiveAction Tilting Cut Here To WAR.I.Gi 10 iN. Jobsite Table SAW Model NO= 137=284630 Schematic a10 iN, Jobsite Parts LiST for MotorTable SAW Model no10 IN. Jobsite Table SAW Parts LiST for StandService Sears Installation ServiceWv sears,tom Wvvv.sears.ca OurHome