Sears 137.28463 operating instructions To prevent serious injury, Fig. WW

Page 38

CROSSCUTTING (Fig. VV)

{_ WARNING]

To prevent serious injury:

o Do not allow familiarity or frequent use of your table saw to cause careless mistakes. Remember that even a careless fraction of a second is enough to cause a severe injury.

o Keep both hands away from the blade and the path of the blade.

o Never attempt to pull the workpiece backwards during a cutting operation. This will cause kickback and serious injury to the

user can occur.

1.Remove the rip fence and place the miter gauge in the miter gauge groove on the table.

2.Adjust the blade height so that it is 1/8 in. higher than the top of the workpiece.

3.Hold the workpiece firmly against the miter gauge with the blade path in line with the desired cut location.

Move the workpiece to a 1 in. distance from the blade.

4.Start the saw and wait for the blade

(1)to come up to full speed. Never stand directly in line of the saw blade path, always stand to the side of the blade that you are cutting on.

5.Keep the workpiece (2) against the face of the miter gauge (3) and flat against the table. Then slowly push the workpiece through the blade.

6.Do not try to pull the workpiece back with the blade turning. Turn the switch OFF, and carefully slide the workpiece out when the blade has completely stopped.

I WARNINGi

Always position the larger surface of the workpiece on the table when crosscutting and/or bevel crosscutting to avoid instability.

Fig. VV

USING THE WOOD FACING ON THE MITER GAUGE (Fig. WW)

Slots are provided in the miter gauge for attaching an auxiliary facing (1) to make it easier to cut very long or short pieces. Select a suitable piece of smooth wood, drill two holes through it and attach it to the miter gauge with screws. Make sure the facing does not interfere with the proper operation of the saw blade guard. When cutting long workpieces, you can make a simple outfeed support by clamping a piece of plywood to a sawhorse.

Fig. WW

/

/

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Operators Manual Section SAW MotorBlade Size PROHiBiTiON Support and Clamp WorkGeneralsafety iNSTRUCTiONS Wear Proper ApparelSecure Page Alwaysusesawblade Page Kickbacks Immediately Power Supply and Motor SPECiFiCATiONSGrounding iNSTRUCTiONS La, Caution Supplied not Supplied Recommended Accessories308K Dado Insert Plate Stand Obtained and is installed correctlyLoose Parts SAW Description Quantity ACD EFG H KLM STUStand lock hook Page Overload Reset Switch Revolutions PER Minute RPMOrder to Avoid iNJURY Do not release the stand hooksSetting UP the Stand Fig. DInstalling the Blade Guard ANTI-KICKBACK PawlsAssembling the Blade Installing the Power CordStorage Clamps Fig. N ELEVATION/TILT HandwheelInstalling the Rear Table Fig. QRiving Knife Assembly Fig. W Anti=kickback pawl assembly Fig. Z, AA, BB Blade Guard AssemblyAdjustments Fig. Y Additional BladeFig. Z Improper riving knife alignment can Fig. DDRiP Fence Adjustment Fig. FF Adjusting the Miter GaugeAdjusting the Table iNSERT Fig. JJ-1 To prevent personal injury BLADETiLTiNG Scale iNDiCATORPower source when making any adjustments Tilting the Blade ON/OFF Switch Fig. NNBasic SAW Operations Cutting Operations Never USE the TWO AT the Same Time TurnthesawONandwaitforthe bladetocometofullspeed Ripping Small Pieces Helpful DevicesMake a Push Block Fig. UU Making the base Auxiliary Fence Fig. TTPush Block To prevent serious injury Fig. WW00~45 Miter Angle Compound Miter CrosscuttingMiTERiNG Fig. ZZ Fig. bb NON-THROUGHDADOCUTSFIG. cc, dd Do not use Adjustable or Wobble type dadoesFor your own safety, always replace Mechanism Fig. ee, ff Maintaining Your Table SAW General MaintenanceBlade Raising and Tilting Replacing the Carbon Clean the Blade Tilting Scale IndicatorLUBRiCATiON Action Problem PossibleCauses Corrective Tilting Cut Here To WAR.I.Gi Schematic a 10 iN. Jobsite Table SAW Model NO= 137=284630Table SAW Parts LiST for Motor10 iN, Jobsite Model noParts LiST for Stand 10 IN. Jobsite Table SAWSears Installation Service ServiceOurHome Wv sears,tom Wvvv.sears.ca
Top Page Image Contents