Sears 137.28463 operating instructions PROHiBiTiON, Support and Clamp Work

Page 4

WARNING iCONS

Your power tool and its Operator's Manual may contain "WARNING iCONS" (a picture symbol intended to alert you to, and/or instruct you how to avoid, a potentially hazardous condition). Understanding and heeding these symbols will help you operate your tool better and safer. Shown below are some of the symbols you may see.

A

®

O

SAFETY ALERT: Precautions that involve your safety.

PROHiBiTiON

WEAR EYE PROTECTION: Always wear safety goggles or safety glasses with side shields.

WEAR RESPIRATORY AND HEARING PROTECTION: Always wear respiratory and hearing protection.

READ AND UNDERSTAND OPERATOR'S MANUAL: To reduce the risk of injury, user and all bystanders must read and understand operator's manual before using this product.

KEEP HANDS AWAY FROM BLADE: Failure to keep your hands away from the blade will result in serious personal injury.

SUPPORT AND CLAMP WORK

,A DANGER I

i,_ WARNING ]

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

IA CAUTION]CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

[ CAUTION ]

CAUTION: Used without the safety alert symbol indicates

a potentially hazardous situation which, if not avoided, may result in property damage.

Image 4

Contents Operators Manual Section Blade Size MotorSAW PROHiBiTiON Support and Clamp WorkGeneralsafety iNSTRUCTiONS Wear Proper ApparelSecure Page Alwaysusesawblade Page Kickbacks Grounding iNSTRUCTiONS Power Supply and Motor SPECiFiCATiONSImmediately La, Caution 308K Dado Insert Plate Recommended AccessoriesSupplied not Supplied Loose Parts SAW Description Quantity Obtained and is installed correctlyStand ACD EFG H KLM STUStand lock hook Page Overload Reset Switch Revolutions PER Minute RPMOrder to Avoid iNJURY Do not release the stand hooksSetting UP the Stand Fig. DInstalling the Blade Guard ANTI-KICKBACK PawlsInstalling the Power Cord Storage Clamps Fig. NAssembling the Blade ELEVATION/TILT HandwheelInstalling the Rear Table Fig. QRiving Knife Assembly Fig. W Blade Guard Assembly Adjustments Fig. YAnti=kickback pawl assembly Fig. Z, AA, BB Additional BladeFig. Z Improper riving knife alignment can Fig. DDRiP Fence Adjustment Fig. FF Adjusting the Miter GaugeAdjusting the Table iNSERT Fig. JJ-1 Power source when making any adjustments BLADETiLTiNG Scale iNDiCATORTo prevent personal injury Basic SAW Operations ON/OFF Switch Fig. NNTilting the Blade Cutting Operations Never USE the TWO AT the Same TimeTurnthesawONandwaitforthe bladetocometofullspeed Ripping Small Pieces Helpful DevicesPush Block Auxiliary Fence Fig. TTMake a Push Block Fig. UU Making the base To prevent serious injury Fig. WWMiTERiNG Fig. ZZ Compound Miter Crosscutting00~45 Miter Angle Fig. bb NON-THROUGHFor your own safety, always replace Do not use Adjustable or Wobble type dadoesDADOCUTSFIG. cc, dd Blade Raising and Tilting Maintaining Your Table SAW General MaintenanceMechanism Fig. ee, ff LUBRiCATiON Clean the Blade Tilting Scale IndicatorReplacing the Carbon Causes Corrective Problem PossibleAction Tilting Cut Here To WAR.I.Gi Schematic a 10 iN. Jobsite Table SAW Model NO= 137=284630Parts LiST for Motor 10 iN, JobsiteTable SAW Model noParts LiST for Stand 10 IN. Jobsite Table SAWSears Installation Service ServiceOurHome Wv sears,tom Wvvv.sears.ca