Sears 137.28463 DADOCUTSFIG. cc, dd, Do not use Adjustable or Wobble type dadoes

Page 41

DADOCUTS(FIG. cc, dd)

i,,_, WARNING]

o Only Stackable dado blades can be used on this saw.

o DO NOT use Adjustable or Wobble type dadoes.

o The maximum dado cut width is 1/2 in.

6.Use only the correct number of round outside blades and inside

chippers as shown in the dado set's instruction manual. Blade/chippers must not exceed 1/2 in. total in width.

Fig. cc

NOTE: An optional dado insert plate (part number 308K) is required for this

J

J

-2

procedure.

1.Remove the table insert, saw blade, anti-kickback pawl assembly, blade guard assembly and riving knife assembly for dado cuts ONLY. Reinstall and realign blade guard for all through-sawing operations. Install a dado not exceeding 6 in. in diameter and 1/2 in. in width

2.Install the dado table insert making sure that the rear of the insert is flush with the table. If the dado insert

is not flush with the table, adjust the two bolts on the insert with a 4 mm hex wrench until it is parallel with the table.

3.Instructions for operating the dado is packed with the separately purchased dado set.

4.The arbor (1) on this saw restricts the maximum width of the cut to 1/2 in.

5.It is not necessary to install the outside flange (2) before threading on the arbor nut (3) for the maximum 1/2 in. dado cuts. Make sure that the

arbor nut (3) is tight, and that at least one thread of the arbor sticks out

past the nut.

-----4-----

1

llitl _H

"3

_N

7.Check the saw to ensure that the dado will not strike the housing, insert, or motor when in operation.

i,A WARNING]

For your own safety, always replace

the blade, blade guard assembly,

anti=kickback pawl assembly,

riving knife assembly and table

insert when you finished the dado

operation.

Fig. dd

Dado cut

Image 41

Contents Operators Manual Section SAW MotorBlade Size Support and Clamp Work PROHiBiTiONWear Proper Apparel Generalsafety iNSTRUCTiONSSecure Page Alwaysusesawblade Page Kickbacks Immediately Power Supply and Motor SPECiFiCATiONSGrounding iNSTRUCTiONS La, Caution Supplied not Supplied Recommended Accessories308K Dado Insert Plate Stand Obtained and is installed correctlyLoose Parts SAW Description Quantity STU ACD EFG H KLMStand lock hook Page Revolutions PER Minute RPM Overload Reset SwitchDo not release the stand hooks Order to Avoid iNJURYFig. D Setting UP the StandANTI-KICKBACK Pawls Installing the Blade GuardStorage Clamps Fig. N Installing the Power CordAssembling the Blade ELEVATION/TILT HandwheelFig. Q Installing the Rear TableRiving Knife Assembly Fig. W Adjustments Fig. Y Blade Guard AssemblyAnti=kickback pawl assembly Fig. Z, AA, BB Additional BladeFig. Z Fig. DD Improper riving knife alignment canAdjusting the Miter Gauge RiP Fence Adjustment Fig. FFAdjusting the Table iNSERT Fig. JJ-1 To prevent personal injury BLADETiLTiNG Scale iNDiCATORPower source when making any adjustments Tilting the Blade ON/OFF Switch Fig. NNBasic SAW Operations Never USE the TWO AT the Same Time Cutting OperationsTurnthesawONandwaitforthe bladetocometofullspeed Helpful Devices Ripping Small PiecesMake a Push Block Fig. UU Making the base Auxiliary Fence Fig. TTPush Block Fig. WW To prevent serious injury00~45 Miter Angle Compound Miter CrosscuttingMiTERiNG Fig. ZZ NON-THROUGH Fig. bbDADOCUTSFIG. cc, dd Do not use Adjustable or Wobble type dadoesFor your own safety, always replace Mechanism Fig. ee, ff Maintaining Your Table SAW General MaintenanceBlade Raising and Tilting Replacing the Carbon Clean the Blade Tilting Scale IndicatorLUBRiCATiON Action Problem PossibleCauses Corrective Tilting Cut Here To WAR.I.Gi 10 iN. Jobsite Table SAW Model NO= 137=284630 Schematic a10 iN, Jobsite Parts LiST for MotorTable SAW Model no10 IN. Jobsite Table SAW Parts LiST for StandService Sears Installation ServiceWv sears,tom Wvvv.sears.ca OurHome