Sears 137.28463 Installing the Power Cord, Storage Clamps Fig. N, Assembling the Blade

Page 22

Rivingknife(Fig. M)

Storage brackets for the riving knife are located on the right side of the stand.

1.Remove the washer (8) and the locking handle (10).

2.Insert riving knife (9) under the set plate (4) and between the retaining clip (7).

3.Tighten the washer (8) and the locking handle (10).

Fig. M

9 i/8

INSTALLING THE POWER CORD

STORAGE CLAMPS (Fig. N)

1.Attach the power cord storage clamp

(1)into the hole set on the rear side of the table saw base with screw (2) and nut (3). NOTE: The nut is placed inside the base.

2.Repeat for the other clamp, to be located on the bottom right on saw base.

Fig. N

Power cord (Fig. O)

Wrap the power cord (2) onto the storage clamps (1) when saw is not in use. This can prevent damage to

the cord. Do not wrap the power cord around the dust port (3).

Fig. 0

1

3

21

ASSEMBLING THE BLADE

ELEVATION/TILT HANDWHEEL

(Fig. P)

1.Attach the blade elevation handwheel (1) to the elevation rod

(2)at the front of the saw. Make sure the slot (3) in the hub of the handwheel (1) engage with the pins (4), turn handle 90 degrees to align pin with the recessed slot to hold the handle in place.

2.Attach and tighten the crown nut

(5)and washer (6) with a 13 mm wrench.

Fig. P

4

1

front view

22

Image 22

Contents Operators Manual Section Blade Size MotorSAW PROHiBiTiON Support and Clamp WorkGeneralsafety iNSTRUCTiONS Wear Proper ApparelSecure Page Alwaysusesawblade Page Kickbacks Grounding iNSTRUCTiONS Power Supply and Motor SPECiFiCATiONSImmediately La, Caution 308K Dado Insert Plate Recommended AccessoriesSupplied not Supplied Loose Parts SAW Description Quantity Obtained and is installed correctlyStand ACD EFG H KLM STUStand lock hook Page Overload Reset Switch Revolutions PER Minute RPMOrder to Avoid iNJURY Do not release the stand hooksSetting UP the Stand Fig. DInstalling the Blade Guard ANTI-KICKBACK PawlsAssembling the Blade Installing the Power CordStorage Clamps Fig. N ELEVATION/TILT HandwheelInstalling the Rear Table Fig. QRiving Knife Assembly Fig. W Anti=kickback pawl assembly Fig. Z, AA, BB Blade Guard AssemblyAdjustments Fig. Y Additional BladeFig. Z Improper riving knife alignment can Fig. DDRiP Fence Adjustment Fig. FF Adjusting the Miter GaugeAdjusting the Table iNSERT Fig. JJ-1 Power source when making any adjustments BLADETiLTiNG Scale iNDiCATORTo prevent personal injury Basic SAW Operations ON/OFF Switch Fig. NNTilting the Blade Cutting Operations Never USE the TWO AT the Same TimeTurnthesawONandwaitforthe bladetocometofullspeed Ripping Small Pieces Helpful DevicesPush Block Auxiliary Fence Fig. TTMake a Push Block Fig. UU Making the base To prevent serious injury Fig. WWMiTERiNG Fig. ZZ Compound Miter Crosscutting00~45 Miter Angle Fig. bb NON-THROUGHFor your own safety, always replace Do not use Adjustable or Wobble type dadoesDADOCUTSFIG. cc, dd Blade Raising and Tilting Maintaining Your Table SAW General MaintenanceMechanism Fig. ee, ff LUBRiCATiON Clean the Blade Tilting Scale IndicatorReplacing the Carbon Causes Corrective Problem PossibleAction Tilting Cut Here To WAR.I.Gi Schematic a 10 iN. Jobsite Table SAW Model NO= 137=284630Table SAW Parts LiST for Motor10 iN, Jobsite Model noParts LiST for Stand 10 IN. Jobsite Table SAWSears Installation Service ServiceOurHome Wv sears,tom Wvvv.sears.ca