Sears 137.28463 operating instructions Installing the Blade Guard, ANTI-KICKBACK Pawls

Page 21

Fig.N	b ) and the. locking.handle (6) to the
Fig.N	ottom ot the set plate (4).
	ottom ot the set plate (4).
	Fig. K	2
	Front

Push stick (Fig. I, J)

Attach the metal push-stick storage bracket (1) into the provided slots (2)

on the right side of the body shell.

The bracket will snap down into place. Place the push stick (3) into the bracket as shown in Fig. J.

Blade wrenches (Fig. J)

Insert the two blade wrenches into the slot (4) located on the right side of the saw housing, under the push stick.

Fig. J

4_._-_--5

1c_-_...._6

Anti-kickback pawls (Fig. L)

Storage for the anti-kickback pawls (1) is located on the right side of the stand.

1.Take the anti-kickback pawl (1) and slide the red locking knob (2) up and press the anti-kickback pawl down to secure the entire assembly on the storage. Release the locking knob (2).

Fig. L

6

4

INSTALLING THE BLADE GUARD,

ANTI-KICKBACK PAWLS AND

RIVING KNIFE STORAGE (Fig. K)

1.Attach the retaining clip (1) to the stand (2) using two screws .(3).

Tighten .screws securely using a screwarwer.

2.Attach the set plate (4) to the stand

(2)using two screws (3) and tighten screws securely. Thread the washer

Blade guard assembly (Fig. L) Storage for the blade guard assembly is located on the right side of the stand.

1.Take the blade guard assembly (5)

and slide the locking knob (6) up and press the guard assembly down so that the entire assembly

is located on the set plate (4). Release the locking knob (6).

Image 21

Contents Operators Manual Section Motor Blade SizeSAW Support and Clamp Work PROHiBiTiONWear Proper Apparel Generalsafety iNSTRUCTiONSSecure Page Alwaysusesawblade Page Kickbacks Power Supply and Motor SPECiFiCATiONS Grounding iNSTRUCTiONSImmediately La, Caution Recommended Accessories 308K Dado Insert PlateSupplied not Supplied Obtained and is installed correctly Loose Parts SAW Description QuantityStand STU ACD EFG H KLMStand lock hook Page Revolutions PER Minute RPM Overload Reset SwitchDo not release the stand hooks Order to Avoid iNJURYFig. D Setting UP the StandANTI-KICKBACK Pawls Installing the Blade GuardStorage Clamps Fig. N Installing the Power CordAssembling the Blade ELEVATION/TILT HandwheelFig. Q Installing the Rear TableRiving Knife Assembly Fig. W Adjustments Fig. Y Blade Guard AssemblyAnti=kickback pawl assembly Fig. Z, AA, BB Additional BladeFig. Z Fig. DD Improper riving knife alignment canAdjusting the Miter Gauge RiP Fence Adjustment Fig. FFAdjusting the Table iNSERT Fig. JJ-1 BLADETiLTiNG Scale iNDiCATOR Power source when making any adjustmentsTo prevent personal injury ON/OFF Switch Fig. NN Basic SAW OperationsTilting the Blade Never USE the TWO AT the Same Time Cutting OperationsTurnthesawONandwaitforthe bladetocometofullspeed Helpful Devices Ripping Small PiecesAuxiliary Fence Fig. TT Push BlockMake a Push Block Fig. UU Making the base Fig. WW To prevent serious injuryCompound Miter Crosscutting MiTERiNG Fig. ZZ00~45 Miter Angle NON-THROUGH Fig. bbDo not use Adjustable or Wobble type dadoes For your own safety, always replaceDADOCUTSFIG. cc, dd Maintaining Your Table SAW General Maintenance Blade Raising and TiltingMechanism Fig. ee, ff Clean the Blade Tilting Scale Indicator LUBRiCATiONReplacing the Carbon Problem Possible Causes CorrectiveAction Tilting Cut Here To WAR.I.Gi 10 iN. Jobsite Table SAW Model NO= 137=284630 Schematic a10 iN, Jobsite Parts LiST for MotorTable SAW Model no10 IN. Jobsite Table SAW Parts LiST for StandService Sears Installation ServiceWv sears,tom Wvvv.sears.ca OurHome