Sears 137.28463 operating instructions BLADETiLTiNG Scale iNDiCATOR, To prevent personal injury

Page 32

BLADETiLTiNG SCALE iNDiCATOR

(Fig. KK)

NOTE: This is located on the top of the table, in front of the blade guard.

1.When the blade is positioned at 90°, adjust the blade tilting scale indicator to read 0°on the scale.

2.Remove the cover (1) by removing the two screws (2). Position the pointer over 0°and replace the cover and the screws.

NOTE: Make a trial cut on scrap wood before making critical cuts. Measure for accuracy.

Fig. KK

BLADE PARALLEL TO THE MITER GAUGE GROOVE (Fig. LL)

[_, WARNING]

This adjustment was made at the factory, but it should be rechecked and adjusted if necessary.

[,A WARNING]

To prevent personal injury:

o Always disconnect plug from the

power source when making any adjustments.

o This adjustment must be correct or accurate cuts can not be made.

Also inaccurate adjustment can result in kickback and serious

personal injury.

1.Remove the safety switch key and unplug the saw.

2.Remove the blade guard for this procedure but reinstall and realign after adjustment.

3.Raise the blade to the highest position and set at the 0° angle (90 ° straight up).

4.Select and mark, with a felt tip marker, a blade tooth having a "right set" and rotate the blade so the marked tooth is 1/2 in. above the table.

5.Place the combination square base

(1)into the right side miter gauge groove (2). (Fig. BB)

6.Adjust the rule so it touches the front marked tooth and lock ruler so it holds

its position in the square assembly.

7.Rotate the blade bringing the marked tooth to the rear and about 1/2 in. above the blade.

8.Carefully slide the combination square to the rear until the ruler touches the marked tooth.

9.If the ruler touches the marked tooth at the front and rear position,

no adjustment is needed at this time. If not or the base of the rule

is no longer parallel with the edge of the miter gauge groove, perform

adjustment procedure described in section ADDITIONAL BLADE

ADJUSTMENTS on page 26.

Fig. LL

32

Image 32

Contents Operators Manual Section SAW MotorBlade Size PROHiBiTiON Support and Clamp WorkGeneralsafety iNSTRUCTiONS Wear Proper ApparelSecure Page Alwaysusesawblade Page Kickbacks Immediately Power Supply and Motor SPECiFiCATiONSGrounding iNSTRUCTiONS La, Caution Supplied not Supplied Recommended Accessories308K Dado Insert Plate Stand Obtained and is installed correctlyLoose Parts SAW Description Quantity ACD EFG H KLM STUStand lock hook Page Overload Reset Switch Revolutions PER Minute RPMOrder to Avoid iNJURY Do not release the stand hooksSetting UP the Stand Fig. DInstalling the Blade Guard ANTI-KICKBACK PawlsInstalling the Power Cord Storage Clamps Fig. NAssembling the Blade ELEVATION/TILT HandwheelInstalling the Rear Table Fig. QRiving Knife Assembly Fig. W Blade Guard Assembly Adjustments Fig. YAnti=kickback pawl assembly Fig. Z, AA, BB Additional BladeFig. Z Improper riving knife alignment can Fig. DD RiP Fence Adjustment Fig. FF Adjusting the Miter GaugeAdjusting the Table iNSERT Fig. JJ-1 To prevent personal injury BLADETiLTiNG Scale iNDiCATORPower source when making any adjustments Tilting the Blade ON/OFF Switch Fig. NNBasic SAW Operations Cutting Operations Never USE the TWO AT the Same TimeTurnthesawONandwaitforthe bladetocometofullspeed Ripping Small Pieces Helpful DevicesMake a Push Block Fig. UU Making the base Auxiliary Fence Fig. TTPush Block To prevent serious injury Fig. WW00~45 Miter Angle Compound Miter CrosscuttingMiTERiNG Fig. ZZ Fig. bb NON-THROUGHDADOCUTSFIG. cc, dd Do not use Adjustable or Wobble type dadoesFor your own safety, always replace Mechanism Fig. ee, ff Maintaining Your Table SAW General MaintenanceBlade Raising and Tilting Replacing the Carbon Clean the Blade Tilting Scale IndicatorLUBRiCATiON Action Problem PossibleCauses Corrective Tilting Cut Here To WAR.I.Gi Schematic a 10 iN. Jobsite Table SAW Model NO= 137=284630Parts LiST for Motor 10 iN, JobsiteTable SAW Model noParts LiST for Stand 10 IN. Jobsite Table SAWSears Installation Service ServiceOurHome Wv sears,tom Wvvv.sears.ca