Sears 137.28463 Recommended Accessories, 308K Dado Insert Plate, Supplied not Supplied

Page 13

RECOMMENDED ACCESSORIES

[,_ WARNING ]

Visit your Sears Hardware Department or see the Craftsman Power and Hand Tools

Catalog to purchase recommended accessories for this power tool.

308K DADO INSERT PLATE

[,_ WARNING ]

To avoid the risk of personal injury:

oDo not use adjustable (wobble) type dadoes or carbide tipped dado blades.

o Only use stackable dadoes.

oMaximum dado width is 1/2 in.

o Do not use a dado with a diameter larger than 6 in.

oDo not use molding head set with this saw.

oDo not modify this power tool or use accessories not recommended by Sears.

SUPPLIED NOT SUPPLIED

Blade wrench	Flat bladed
	screwdriver
Phillips		screwdriver
Blade wrench
[!	!! !!	!!	!! !! ]
	Straight		edge

4 mm hex wrench

Adjustable wrench and/or 8 mm, 10 mm,

13 mm, 14 mm,

17 mm wrench

Combination square

Image 13

Contents Operators Manual Section Blade Size MotorSAW Support and Clamp Work PROHiBiTiONWear Proper Apparel Generalsafety iNSTRUCTiONSSecure Page Alwaysusesawblade Page Kickbacks Grounding iNSTRUCTiONS Power Supply and Motor SPECiFiCATiONSImmediately La, Caution 308K Dado Insert Plate Recommended AccessoriesSupplied not Supplied Loose Parts SAW Description Quantity Obtained and is installed correctlyStand STU ACD EFG H KLMStand lock hook Page Revolutions PER Minute RPM Overload Reset SwitchDo not release the stand hooks Order to Avoid iNJURYFig. D Setting UP the StandANTI-KICKBACK Pawls Installing the Blade GuardStorage Clamps Fig. N Installing the Power CordAssembling the Blade ELEVATION/TILT HandwheelFig. Q Installing the Rear TableRiving Knife Assembly Fig. W Adjustments Fig. Y Blade Guard AssemblyAnti=kickback pawl assembly Fig. Z, AA, BB Additional BladeFig. Z Fig. DD Improper riving knife alignment canAdjusting the Miter Gauge RiP Fence Adjustment Fig. FFAdjusting the Table iNSERT Fig. JJ-1 Power source when making any adjustments BLADETiLTiNG Scale iNDiCATORTo prevent personal injury Basic SAW Operations ON/OFF Switch Fig. NNTilting the Blade Never USE the TWO AT the Same Time Cutting OperationsTurnthesawONandwaitforthe bladetocometofullspeed Helpful Devices Ripping Small PiecesPush Block Auxiliary Fence Fig. TTMake a Push Block Fig. UU Making the base Fig. WW To prevent serious injuryMiTERiNG Fig. ZZ Compound Miter Crosscutting00~45 Miter Angle NON-THROUGH Fig. bbFor your own safety, always replace Do not use Adjustable or Wobble type dadoesDADOCUTSFIG. cc, dd Blade Raising and Tilting Maintaining Your Table SAW General MaintenanceMechanism Fig. ee, ff LUBRiCATiON Clean the Blade Tilting Scale IndicatorReplacing the Carbon Causes Corrective Problem PossibleAction Tilting Cut Here To WAR.I.Gi 10 iN. Jobsite Table SAW Model NO= 137=284630 Schematic a10 iN, Jobsite Parts LiST for MotorTable SAW Model no10 IN. Jobsite Table SAW Parts LiST for StandService Sears Installation ServiceWv sears,tom Wvvv.sears.ca OurHome