Sears 137.28463 operating instructions Fig. Z

Page 27

. Place the front of assembly into the back slot on the riving knife and

push downward. Release the locking knob. Make sure the lock knob is

engaged in the hole and that there is no movement of the assembly.

(Fig. Z)

Fig. Z

. Take the blade guard assembly and locate the red sliding locking knob

(3)on the back of assembly. (Fig. AA)

Fig. AA

6

5.Insert the blade guard assembly onto the riving knife so that the pin

(4)engages into slot (5) completely. (Fig. BB)

6.Slide the red locking knob (3) up and press the guard assembly down so that the entire assembly is flat on the riving knife. Release the locking knob (3).

7.Make sure that the assembly is locked in place both in front and back.

Fig. BB

5

4

Removing the blade guard and anti-kickback pawl assembly (Fig. Z, BB)

I,,_ WARNING]

To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is

disconnected from the power source outlet.

1.With the blade elevation handwheel raise the blade to the maximum height.

2.Loosen the blade lock handle and then turn the handwheel to 45° on the bevel scale.

3.Tighten the bevel lock handle.

4.Remove the anti-kickback pawl assembly by pressing up on the red knob (2) and lifting the assembly off the riving knife. (Fig. Z)

5.Remove the blade guard assembly by pressing up on the red knob

(3)and lifting the assembly off the riving knife. (Fig. BB)

27

Image 27

Contents Operators Manual Section Motor Blade SizeSAW Support and Clamp Work PROHiBiTiONWear Proper Apparel Generalsafety iNSTRUCTiONSSecure Page Alwaysusesawblade Page Kickbacks Power Supply and Motor SPECiFiCATiONS Grounding iNSTRUCTiONSImmediately La, Caution Recommended Accessories 308K Dado Insert PlateSupplied not Supplied Obtained and is installed correctly Loose Parts SAW Description QuantityStand STU ACD EFG H KLMStand lock hook Page Revolutions PER Minute RPM Overload Reset SwitchDo not release the stand hooks Order to Avoid iNJURYFig. D Setting UP the StandANTI-KICKBACK Pawls Installing the Blade GuardELEVATION/TILT Handwheel Installing the Power CordStorage Clamps Fig. N Assembling the BladeFig. Q Installing the Rear TableRiving Knife Assembly Fig. W Additional Blade Blade Guard AssemblyAdjustments Fig. Y Anti=kickback pawl assembly Fig. Z, AA, BBFig. Z Fig. DD Improper riving knife alignment canAdjusting the Miter Gauge RiP Fence Adjustment Fig. FFAdjusting the Table iNSERT Fig. JJ-1 BLADETiLTiNG Scale iNDiCATOR Power source when making any adjustmentsTo prevent personal injury ON/OFF Switch Fig. NN Basic SAW OperationsTilting the Blade Never USE the TWO AT the Same Time Cutting OperationsTurnthesawONandwaitforthe bladetocometofullspeed Helpful Devices Ripping Small PiecesAuxiliary Fence Fig. TT Push BlockMake a Push Block Fig. UU Making the base Fig. WW To prevent serious injuryCompound Miter Crosscutting MiTERiNG Fig. ZZ00~45 Miter Angle NON-THROUGH Fig. bbDo not use Adjustable or Wobble type dadoes For your own safety, always replaceDADOCUTSFIG. cc, dd Maintaining Your Table SAW General Maintenance Blade Raising and TiltingMechanism Fig. ee, ff Clean the Blade Tilting Scale Indicator LUBRiCATiONReplacing the Carbon Problem Possible Causes CorrectiveAction Tilting Cut Here To WAR.I.Gi 10 iN. Jobsite Table SAW Model NO= 137=284630 Schematic aModel no Parts LiST for Motor10 iN, Jobsite Table SAW10 IN. Jobsite Table SAW Parts LiST for StandService Sears Installation ServiceWv sears,tom Wvvv.sears.ca OurHome