Hobart Welding Products CHAMP 2060 manual Operating Auxiliary Equipment

Page 25

SECTION 6 – OPERATING AUXILIARY EQUIPMENT

NOTE

The welding generator provides power while welding and with the Current control in any position. However, under these conditions equipment connected to the welding generator may be subject to larger than normal voltage fluctuations. It is recommended that only lamps be powered under these conditions.

6-1. Generator Power Panel 495 218 (USA)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

1

2

3

5

YIf unit does not have GFCI recep- tacles, use GFCI-protected exten- sion cord.

YPower is still present at the 240 volt receptacle when only one circuit breaker trips.

Unplug power cord before attempt- ing to service accessories or tools.

.Generator power decreases as weld current increases.

Set Amperage control at max. for full generator power.

.Place throttle lever in Run position (far right) for generator power.

1 120 V AC Twistlock Receptacle RC1

RC1 supplies 60 Hz single-phase power at weld/power speed. Maximum output is 3.5 kVA/kW.

2120 V 20 A AC Duplex Receptacle RC2

3120 V 20 A AC Duplex Receptacle RC3

RC2 and RC3 supply 60 Hz single-phase power at weld/power speed. Maximum output from RC2 or RC3 is 2.4 kVA/kW.

.Each receptacle of the duplex can pro- vide 15A/1800W.

.Do not parallel the two 120V duplex receptacles.

4 Circuit Breaker CB1

CB1 protects RC1 from overload. If CB1 opens, RC1 does not work.

495 218

5 Circuit Breakers CB2 And CB3

CB2 protects RC2 and CB3 protects RC3 from overload. If a circuit breaker opens, the receptacle does not work.

.Press button to reset circuit breaker. If breaker continues to open, contact Factory Authorized Service Agent.

Combined output of all receptacles limited to 6 kVA/kW rating of the generator (See Section 10 – Generator Power Guide- lines).

EXAMPLE: If 10 A is drawn from each 120 volt duplex receptacle, only 9 A is available from the 120 V twistlock receptacle.

2 x (120 V x 10 A) + (240 V x 9 A) = 3.5 kVA/ KW.

OM-499 Page 21

Image 25
Contents Processes OM-499Description From Hobart to You Table of Contents Page Arc Welding Hazards Marks a special safety messageElectric Shock can kill Fumes and Gases can be hazardousEngine Hazards Compressed Air Hazards EMF Information Principal Safety StandardsConsignes DE Sécurité Lire Avant Utilisation Signification des symbolesUN Choc Électrique peut tuer LES Fumées ET LES GAZ peuvent être dangereuxDES Particules Volantes peuvent blesser les yeux LE Soudage peut provoquer un in- cendie ou une explosionDES Pièces Chaudes peuvent Provoquer des brûlures gravesDES Organes Mobiles peuvent provoquer des blessures ’EXPLOSION DE LA Batterie peutLA Chaleur DU Moteur peut pro- voquer un incendie ’AIR Comprimé peut provoque r des blessuresInformation sur les champs électromagnétiques Principales normes de sécuritéSymbol Definitions SpecificationsWeld, Power, And Engine Specifications Welding Weld Output Rated Maximum Generator PowerFuel Consumption Kohler-Powered Units Dimensions, Weights, And Operating AnglesDo not move or operate unit where it Be damaged or unit could tipExceeding duty cycle can damage unit and void warranty Fuel Consumption Honda-Powered UnitsDuty Cycle Continuous WeldingHz Model Generator Power CurvesMAX MID MIN Volt-Ampere CurvesInstalling Welding Generator InstallationGrounding Generator To Truck Or Trailer Frame Engine Prestart Checks Kohler-Powered Units Grounding Generator When Supplying Building SystemsFuel OilConnecting The Battery Electric-Start Models Only Engine Prestart Checks Honda-Powered UnitsConnect negative cable last Selecting Weld Cable Sizes Connecting To Weld Output Terminals45 m 60 m 70 m 90 m 105 m 120 m Stop engine beforeOperating the Welding Generator Controls Kohler-Powered Units50 Hz 60 Hz Recoil-Start 2Electric-Start Controls Honda-Powered Units See Section60 Hz 50 Hz Description Of Controls Honda-Powered Units See Section Operating Auxiliary Equipment Generator Power Panel 495 218 USA120 V x 10 a + 240 V x 9 a = 3.5 kVA/ KW OM-499 Generator Power Panel 495 Optional Generator Power PanelsCanada-CSA South Africa South America Australia Europe AsiaIt exceeds 5500W Generator Power Panel RatingsMaintenance Label Maintenance20 h Routine Maintenance50 h 100 hAdjusting Engine Speed Kohler-Powered Units Overload Protection Honda-Powered UnitsWeld/Power Speed Adjustment Idle Speed AdjustmentThrottle Control Lever Adjustment Screw Adjusting Engine Speed Honda-Powered UnitsPilot Screw Throttle Stop Screw Stop engine. Close fuel valveTroubleshooting TroubleshootingGenerator Power WeldingViscosity oil for operating temperature Check battery voltage electric-start models onlyEngine Circuit board PC1Circuit Diagram For Welding Generator 1 Electrical DiagramsCircuit Diagram For Welding Generator 2 Wiring Diagram For Welding Generator Wiring Diagram For Auxiliary Power Panels 1 Wiring Diagram For Auxiliary Power Panels 2 Selecting Equipment Generator Power GuidelinesHow Much Power Does Equipment Require? Grounding When Supplying Building SystemsEarth ground if supplying Volts 115 Amps Resistive LoadApproximate Power Requirements For Farm/Home Equipment Approximate Power Requirements For Industrial MotorsIndustrial Motors Rating Starting Watts Running Watts Farm/Home Equipment Rating Starting Watts Running WattsContractor Rating Starting Watts Running Watts Approximate Power Requirements For Contractor EquipmentHow Much Power Can Generator Supply? Power Required To Start MotorSingle-Phase Induction Motor Starting Requirements KVA/HP x HP xWork like a Pro Typical Connections To Supply Standby PowerCurrent Load Watts Amperes Selecting Extension Cord Use Shortest Cord PossibleWeld current starts when electrode touches work- piece Stick Welding ProcedureStick Welding Smaw Guidelines Striking an Arc Scratch Start Technique Electrode and Amperage Selection ChartStriking an Arc Tapping Technique Good Weld Bead Characteristics Poor Weld Bead CharacteristicsPositioning Electrode Holder 10-30 9090 End View of Work AngleElectrode Movement During Welding Conditions That Affect Weld Bead ShapeLap Joint Butt JointsTee Joint 16 in 1.6 mm Tack WeldsTroubleshooting Excessive Spatter Troubleshooting PorosityWeld Test Possible Causes Corrective ActionsTroubleshooting Lack Of Penetration Troubleshooting Incomplete FusionTroubleshooting Excessive Penetration Troubleshooting Waviness Of Bead Troubleshooting Burn-ThroughTroubleshooting Distortion Main Assembly Parts ListDia Part Dia Part Mkgs Description Quantity Generator Power Panels Item Dia Part Mkgs Description Quantity Support ServiceHobart Welding Products Contact your Distributor for