Southbend SB1024, SB1026, SB1025 owner manual Spindle Break-In, Inspections Adjustments

Page 29

For Machines Mfg. Since 8/09

P R E P A R A T I O N

SB1024/SB1025/SB1026

Spindle Break-In

Complete the spindle bearing break-in procedure to avoid rapid deterioration of spindle components when the mill is placed into operation.

The high-quality bearings and gears used in the mill are manufactured to very close tolerances. However, this does not guarantee perfect dimensional mating of the bearing components or exact meshing of gear teeth. Before operational stress is placed on these and other moving parts in the mill, complete this break-in procedure to conform these components to one another and ensure trouble-free performance from the mill.

To perform the spindle break-in procedure:

1.Successfully perform all the steps in the Test Run section beginning on Page 25.

2.Make sure the spindle is at a complete stop.

3.Set the spindle speed to the low range (refer to Setting Spindle Speed Range beginning on Page 37 for detailed instructions).

4.Start the spindle rotation at a medium speed and let the mill run for 20 minutes.

5.Stop the spindle rotation and allow the spindle to come to a complete stop by itself.

6.Set the spindle speed to the high range, then start the spindle rotation at a medium speed and let the mill run for another 20 minutes.

7.Stop the spindle rotation, and turn the mill OFF.

The spindle break-in of the mill is now complete!

Since the mill head was rotated parallel to the table for shipping purposes, you will need to tram the spindle with the table if your first cut requires a 90° alignment. Refer to the Tramming Spindle section on Page 33 for detailed instructions.

Inspections &

Adjustments

The following list of adjustments were performed at the factory before the machine was shipped:

ss Gib Adjustment

Page 58

ssLeadscrew Backlash

Adjustment

Page 59

Be aware that machine components can shift during the shipping process. Pay careful attention to these adjustments during operation of the machine. If you find that the adjustments are not set according to the procedures in this manual or your personal preferences, re-adjust them.

-27-

Image 29
Contents 42 Milling Machine Customer Service UpdatesScope of Manual Manual FeedbackTable of Contents Parts About These Machines FeaturesForeword CapabilitiesIdentification-front view Model SB1024 shown Front View IdentificationModel SB1024 belt housing and headstock identification Model SB1024 Belt Housing Headstock IdentificationModel SB1025/SB1026 Belt Housing Headstock Identification Machine Specifications Model SB1024 42 Variable Speed Milling Machine Power FeedTable Information Model SB1025 42 Milling Machine Power Feed 80, 140, 220, 325 RPM Model SB1026 42 Milling Machine Power Feed High Range of Spindle Speeds Understanding Risks of Machinery Basic Machine SafetyF E T Y Additional Milling Machine Safety Things Youll Need Preparation OverviewInventory UnpackingBasic steps for removing rust preventative Cleaning & ProtectingBefore cleaning, gather the following Location To lift and move the mill Lifting & MovingLeveling Leveling & MountingBolting to Concrete Floors To install the ball handles AssemblyBall Handles Knee CrankWay Covers Front way cover installedSB1025 220V 3-Phase Power ConnectionSB1024 SB1026To test run the machine Initial LubricationTest Run To test the X-axis power feed unit and table limit switch Spindle Break-In Inspections AdjustmentsTo perform the spindle break-in procedure A typical milling operation, the operator does the following Operation OverviewTable Movement Control PanelTable Locks Graduated Index RingsTo operate the X-axis power feed Axis Power FeedTilting Head Head MovementTramming Spindle Rotating HeadTools Needed Qty To tram the spindle to the tablePlace the parallel block directly under Rotating Ram Ram MovementMoving Ram Back-and-Forth Determining Spindle Speed Setting Spindle SpeedSetting Spindle Speed Range Model SB1024 Spindle Speed Ranges Setting SB1024 Spindle Speed RangeModel SB1025 Spindle Speed Ranges Setting SB1025/SB1026 Spindle Speed RangeMeshing Spindle & Spindle Clutch Setting SB1024 Spindle Speed Setting Spindle SpeedF2/R2 Setting SB1025/SB1026 Spindle SpeedDownfeed Controls Using the Coarse Downfeed HandleManual Disengaged Position Auto-Downfeed Engaged Position Fine Downfeed Controls Using the Fine Downfeed HandwheelTo use the auto-downfeed system Using the Auto-Downfeed System= 0.006 in./rev = 0.0015 in./rev = 0.003 in./rev Spindle BrakeUnloading Tooling Loading/Unloading ToolingLoading Tooling Before Beginning Operations Maintenance ScheduleOngoing Daily, After OperationsLubrication Month/YearUnpainted & Machined Surfaces CleaningLubrication Table Ways One-Shot Oiler QuillHeadstock Gearing Speed Range Bearing Sleeve SB1024 OnlyTo lubricate the power feed gears Power Feed GearsRam Ways Head & Ram Rack & Pinion GearPower feed ball handle removed Drive Gear Bevel Gear Cleaning Cleaning Coolant ReservoirTo clean out the coolant reservoir HazardsLubrication section beginning on Machine StorageDisconnect Mill from Power Before Adjusting the Gibs Adjusting GibsLongitudinal Leadscrew Backlash Adjusting Leadscrew BacklashBall handle, rings, and key removed from Cross leadscrew Cross Leadscrew BacklashSymptom Possible Cause Possible Solution TR O U B L E S H O OTI N G Electrical Safety Instructions Wiring Diagram Color KEY Wiring OverviewBox, See SB1024/SB1026 Electrical BoxControl Panel Viewed From Behind See Figure SB1024/SB1026 Electrical ComponentsMotor junction box SB1024/SB1026 Electrical Component PicturesSB1025 Electrical Box SB1025 Electrical Components SB1025 Motor junction box SB1025 Electrical Component PicturesHeadstock Description Headstock Parts ListReverse Trip Ball Lever Quill SB1024 Gearbox Description SB1024 Gearbox Parts ListSB1025/SB1026 Gearbox SB1025/SB1026 Gearbox Parts List SB1024 Belt Housing SB1024 Belt Housing Parts List SB1025/SB1026 Belt Housing CAM Ring Screw M6-1 X SB1025/SB1026 Belt Housing Parts ListRam Ram Parts List 668 Saddle GIB Column, Knee, & Saddle Parts List709 Leadscrew NUT Bracket Table Parts ListC D E F G H One-Shot OilerElectrical Box SB1024/SB1026 Electrical Box & Control PanelControl Panel SB1025 Electrical Box & Control PanelAccessories SB1024 Head Machine Labels 220V 1PH Label SB1024 Main Machine LabelsSB1025/SB1026 Machine Labels Page R R a N T Y Southbendlathe.com