Southbend SB1023 Test Run, Inspections Adjustments, Initial Lubrication, To test run your machine

Page 18

Model SB1023

 

P R E P A R A T I O N

For Machines Mfg. Since 8/09

Initial Lubrication

 

unusual noises or vibrations before

 

 

 

• Investigate and correct strange or

Your machine was lubricated at the factory,

operating the machine further. Always

stop the machine and disconnect it from

but we strongly recommend that you inspect all

power before investigating or correcting

lubrication points yourself and provide additional

potential problems.

lubrication if necessary. Refer to Lubrication on

 

 

Page 30 for specific locations.

7.

Press the STOP button.

 

 

Test Run

After all preparation steps have been completed, the machine and its safety features must be tested to ensure correct operation. If you discover a problem with the operation of the machine or its safety components, do not operate it further until you have resolved the problem.

Refer to Troubleshooting on Page 34 for solutions to common problems that may occur with surface grinders. If you need additional help, contact our Technical Support at (360) 734-1540.

To test run your machine:

1.Read and follow the safety instructions at the beginning of the manual, take the required safety precautions, and make sure the machine is set up and adjusted properly.

2.Ring test the grinding wheel, and install the wheel onto the spindle.

Refer to Ring Test on Page 25, and

Installing & Removing Grinding Wheels on Page 20 for procedures.

3.Clear away all tools and objects used during assembly and preparation.

4.Connect the machine to the power source.

5.Push the STOP button in, then twist it clockwise so it pops out. When the STOP button pops out, the switch is reset and ready for operation.

6.Verify that the machine is operating correctly by pushing the START button.

•When operating correctly, the machine runs smoothly with little or no vibration or rubbing noises.

8.WITHOUT resetting the switch, press the START button. The machine should not start.

•If the machine does not start, the STOP button safety feature is working correctly.

•If the machine does start (with the stop button pushed in), immediately disconnect power to the machine. The STOP button safety feature is not working correctly. This safety feature must work properly before proceeding with regular operations. Call Tech Support for help.

Inspections &

Adjustments

The following list of adjustments were performed at the factory before your machine was shipped:

•Ring Test on Page 25

•Wheel Dressing on Page 25

•Wheel Balancing on Page 26

•Lubrication on Page 30

•Handwheel Backlash Adjustment on

Page 32

•Column & Table Gib Adjustment on

Page 32

-16-

Page 17 Page 19
Image 18
Page 17 Page 19
Contents 12 Surface Grinder Scope of Manual UpdatesCustomer Service Manual FeedbackTable of Contents Features About This MachineCapabilities Identification IdentificationMachine Specifications Model SB102312 Surface Grinder Main Specifications Operation Information Basic Machine Safety Understanding Risks of MachineryF E T Y Additional Surface Grinder Safety Things Youll Need For Power ConnectionFor Assembly Typical preparation process is as followsUnpacking InventoryCleaning & Protecting Before cleaning, gather the followingBasic steps for removing rust preventative Location Lifting & Moving Leveling & MountingLeveling Assembly To install the feetTo convert the Model SB1023 to operate on 220V power Power ConnectionSB1023 110V Prewired SB1023 220V OptionInitial Lubrication Inspections AdjustmentsTest Run To test run your machineOperationPERATIONOverview Controls Control panelGrit Size Wheel SelectionAbrasive Type GradeRemoving & Installing Grinding Wheels To remove and install a grinding wheelRemove the grinding wheel, as shown in Figure Removing & Installing Wheel & Hub To remove and reinstall the wheel and hubRemove the spindle bolt Figure Wheel Inspection To inspect a wheel for damageRing Test Wheel DressingTo perform a ring test Wheel Balancing To dress the grinding wheelTo balance the grinding wheel I N T E N a N C E Setup for a Typical Grinding Operation Magnetic ChuckGrinder Operation Using the Surface Grinder Grinding TipsDaily Maintenance ScheduleLubrication Bi-weeklyLower column leadscrew Column & Table Gib Adjustment Handwheel Backlash AdjustmentMachine Storage Short-term storage less than yearLongng-term-termstoragestorage more than a year Troubleshooting Troubleshooting Lectrical Safety Instructions Wiring Diagram Color KEYSB1023 Wiring Diagram MotorMotor Wired for Motor & Spindle DescriptionColumn See Table Parts List on Column Parts List Table Parts ListStand Machine Labels R R a N T Y #CRJB12368
Top Page Image Contents