DeWalt Twist-lock Connector DWS535T, Cutting Depth Adjustment 4, Bevel Angle Adjustment

Page 9

Your saw has a convenient saw hook that allows the saw to hang from a joist, rafter, or other suitable, stable structure. The saw hook folds flat against the tool body when not in use.

To use the saw hook, push down on the hook to rotate it away from the handle until it latches into position.

To return the saw hook to its stored position, pull the hook up until it latches against the tool body.

Twist-lock Connector _DWS535T)

FIG. 3

The DWS535T is equipped with a twist-lock connector as shown in Figure 3. This prevents the cord from unplugging if the cord is

inadvertantly pulled. Only plug the twist-lock connector into a 3-wire extension cord with a female connector.

Cutting Depth Adjustment (Fig. 1_ 4_ 5)

1.Hold the saw firmly. Lift the depth adjustment locking lever (B) to move foot plate to obtain the desired depth of cut.

2.Lower the depth adjustment locking lever and tighten securely to lock the depth of cut before operating saw.

The length of cut markings on the side of the foot plate are accurate at full depth of cut only. Setting the saw at the proper cutting depth keeps blade friction to a minimum, removes sawdust from between

the blade teeth, results in cooler, faster sawing and reduces the chance of kickback.

FIG. 4

FIG. 5

GULLET OF BLADE

TOOTH

For the most efficient cutting action, set the depth adjustment so that half of a blade tooth will project below the material to be cut. This distance is from the tip of the tooth to the bottom of the gullet in front of it (refer to inset of Figure 5). This keeps blade friction at a minimum, removes sawdust from the cut, results in cooler, faster sawing and reduces the chance of kickback. A method for checking for correct cutting depth is shown in Figure 5. Lay a piece of the material you plan to cut along the side of the blade, as shown, and observe how much tooth projects beyond the material.

Bevel Angle Adjustment (Fig. 1_ 6)

The

full range

of

the

FIG. 6

bevel

adjustment

is from

 

0° to

53 °. Detents

are

N

located at 22.5 ° and 45 °.

The angle quadrant is

graduated in increments I of 1° On the front of the

saw is a bevel angle adjustment mechanism

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Manual DE Instrucciones DWS535, DWS535T =1/4 184 ramWorm Drive Saw General Power Tool Safety Warnings Definitions Safety GuidelinesWork Area Safety Electrical SafetyPower Tool USE and Care Personal SafetySafety Instructions for All Saws ServiceCauses and Operator Prevention of Kickback Kickback Lower Guard Safety InstructionsMinimum Gauge for Cord Sets Saw Nook CCATwist-lock Connector DWS535T Cutting Depth Adjustment 4Bevel Angle Adjustment Trigger Switch Fig Foot Plate Adjustment ForKerr Indicator Fig Changing BladesTo Remove Knockout To Installthe Blade , 10To Replace the Blade FIG Blades KickbackLower Blade Guard Improper Workpiece SupportWorkpiece Support Fig Cutting Ripping FIG RIP GuidePocket Cutting FIG To Check OIL LubricationYear Free Service DAY Money Back GuaranteeBrushes Fig 0WS535 ,-,/,!18,o,mlwoRMDRIVECIRCO,A,SAW FIG1 Avertissernents de scurit gdnraux Dfinitions lignes directricesPour ies outils iectriques Ere rnatire de scuritSecuriti Personnelle Consignes de scurit propres routes les sties Utilisation ET Entretien Dunoutil ¢LECTRIQUEReparation Page Consignes DE Sicurite Relatives AU PROTEGE-LAME Inferieur Consignes additionneiles de scuriteAWG Usage Privu Description FIGRglage de profondeur de coupe De suspensionConnecteur verrouiUage par rotation AvertissementIndicateur de trait de scie Fig Rglage de la plaque dassise pour desReglage DE LA Scie Pour Effectuer UNE Coupe EN Biseau Retrait DE Lalisage Amovible Gachette FigInstallation DE LA Lame ,10 Resserrez Pour Changer LA Lame FIGLames RebondsCarter DE Lame Inferjeur Torsion DE LA Lame Mpsalignement DE Coupe Coupe Support de piece FigCoupe Longitudinale FIG Coupe Interne FIG Nettoyage#RJFICATION DE Lhujle LubrificationService Dentretien Gratuit DE 1 AN Garantie lirJit#.e trois artsGarantie DE Remboursement DE 90 Jours DWS535 ,-,/,l,8,olwoo.M.ivEcl.cus.,.w Remplacement Gratuit DES ItiquettesSierra de 184 mm 7=1/4 pulg. con impulsor sinfin Seguridad Definiciones Norrnas deSeguridad EN EL Area DE Trabajo Seguridad ElectricaUSO Y Mantenimiento DE LA Herramienta Elictrica Seguridad PersonalPeligro Instrucciones de seguridad para todas las sierrasCausas DEL Retroceso Y SU PREVENClON POR EL Operador Instrucciones DE Seguridad Para EL Protector Inferior Instrucciones adicionales de seguridadCable Componentes FIG Ajuste de la profundidad del corte Garecho La sierraUSO Debido AdvertenciaAjuste de la plataforrna Ajuste dei aregulo del biselPunta Diente Para Ajustar LA Sierra Para UN Corte BiseladoInterrupter de gatille Fig Indicader de linea de torte FigPara carnbiar las hojas Para Abrir EL Orificio PRE-HORADADOPara Instalar LA Hoja , 10 FIG10 Hojas Para Cambiar LA Hoja FIGProtector Inferior DE LA Hoja Retroceso Soporte Inadecuado DE LA Pieza DE TrabajoAjuste Inadecuado DE LA Profundidad DE Corte EN LA Sierra Torsion DE LA Hoja Desaljneacjon EN EL Corte Apoyo de ia pieza de trabajo FigUtimzacjon DE Hojas Romas O Sucias Para Levantar LA Sierra AL Cortar CON BiselCorte LO Largo DE LA VETADWS5100 DW3278 Cortes DE Orifioios FIG Cortar a LO Largo DE Laveta FIGLimpieza Lubricaci6nPara Comprobar EL Aceite £scobillas Fig P61iza De Garantia Garantia lirnitada por tres aosIdentificacion DEL Producto CUUACAN, SN DWS535,-,/.l,..mwo.,vEc,.M.cusawGuadalajara JAL MEXICO, D.FMonterrey MERIDA, YUCPUEBLA, PUE QUERETARO, QRO
Related manuals
Manual 64 pages 16.25 Kb

DWS535T, DWS535 specifications

The DeWalt DWS535 is a powerful and versatile circular saw that is designed to meet the rigorous demands of professionals and DIY enthusiasts alike. Known for its solid construction and cutting-edge technology, the DWS535 showcases the brand's commitment to quality and innovation in woodworking tools.

One of the standout features of the DWS535 is its robust 15-amp motor, which delivers a remarkable no-load speed of 5,300 RPM. This ensures users can tackle a variety of cutting tasks with ease and confidence, whether working with lumber, engineered wood products, or other materials. The high-speed blade cuts through even the toughest materials quickly and efficiently, making it ideal for framing, decking, and general carpentry projects.

The DWS535 is equipped with a 7-1/4 inch carbide-tipped blade that enhances cutting accuracy and durability. The blade's design allows for smooth and clean cuts, reducing the need for post-processing. Additionally, the saw’s integrated electric brake stops the blade quickly after the trigger is released. This safety feature not only enhances user control but also minimizes the risk of accidental injuries, making it a safer choice for operators.

Comfort and usability are also central to the design of the DWS535. It features a lightweight, well-balanced construction that allows for easy maneuverability. Furthermore, the ergonomic handle is designed to reduce fatigue during extended use, providing better grip and control. The saw’s bevel capacity of 0° to 45° contributes to its versatility, enabling users to achieve angled cuts with precision.

Incorporating advanced technologies, the DWS535 features a built-in rafter hook that provides convenient storage and accessibility. Additionally, the saw is designed with a durable protective blade guard that enhances safety while allowing users to easily visualize their cutting line. The tool’s dust port is another thoughtful addition, helping to keep the workspace clean and free from debris, ultimately improving visibility for better accuracy.

Overall, the DeWalt DWS535 stands out in a crowded market of circular saws with its powerful performance, safety features, and user-friendly design. Whether you’re a seasoned professional or a weekend warrior, this tool is engineered to deliver efficiency, accuracy, and safety on every job site. With its remarkable combination of features, the DWS535 proves to be a wise investment for anyone serious about woodworking or construction.
Top Page Image Contents