Manuals / Xantrex Technology / Computer Equipment / Power Supply

Xantrex Technology XDC manual Gpib Operation, Gpib Pins

Models: XDC

1 254

Download 254 pages 27.31 Kb

Page 122

Remote Operation

GPIB Operation

GPIB Operation

GPIB The GPIB port is a special GPIB female connector. Table 4.7 describes the pin Connection functions. Pin 12 is not used.

Table 4.7	GPIB Pins
Pin #	Function
1	D1

2	D2

3	D3

4	D4

5	EOI

6	DAV

7	NRFD

8	NDAC

9	IFC

10	SRQ

11	ATN

12	Not used

13	D5

14	D6

15	D7

16	D8

17	REN

18	Ground

19	Ground

20	Ground

21	Ground

22	Ground

23	Ground

24	Ground

120	Operating Manual for XDC Series Power Supply

Image 122

Xantrex Technology XDC manual Gpib Operation, Gpib Pins

Contents

Operating Manual Page Operating Manual for What will Xantrex do? How do you get service?What does this warranty cover and how long does it last? Phone 604 422 Toll Free North America 800 667 Fax 604 421What does this warranty not cover? Disclaimer Product Model Number Serial Number Purchased From Purchase Date Information About Your Power SupplyRelease Release 3.0 Power Supply Safety Symbols Used in This ManualFCC Part 15 Radio Frequency Devices Class a Limits Approvals CE MarkCSA C22.2 No Unit complies with Canadian EMC requirements of ICES-001About This Manual Who Should Use This Manual Navigation SectionsRevisions About This ManualContents Contents OperationContents Remote OperationCurrent Sharing 6000 Watt only Appendix A. CalibrationAppendix B. Scpi Command Reference Appendix C. Error MessagesIndex Appendix E. Specifications and CharacteristicsAppendix D. Gpib List of Tables List of Tables List of Figures List of Figures About The XDC Power Supply OverviewFront Panel 6000 Watt About The XDC Power SupplyFront Panel Front Panel 12000 Watt Keypad About The XDC Power Supply Key Functions Special Key FunctionsMenu Function Front Panel Display DisplayStatus Annunciators Front Panel Display, Status AnnunciatorsStatus Annunciators Rear Panel Rear Panel 6000 Watt low and medium output shownOverview of Operation About The XDC Power Supply Basic Setup Procedure Inspection Inspection, Cleaning, and PackagingInitial Returning Power Supplies to the Manufacturer Packaging for Shipping or Storage Typical Box Label for StorageRack Mounting To install the power supply in an equipment rackLocation, Mounting, and Ventilation Unpacking the Power Supply 6000 Watt shown Installation AC Input Power AC Input Connector for 6000 Watt unitsAC Input Voltage Range Wire AC Wire Input Connection For 6000 WAC Wire Specification for 6000 Watt units Attaching the AC Input Wires for 6000 Watt units AC Wire Input Connection for 12000 W Attaching the AC Input Wires for 12000 Watt units Basic Checks or Self-Tests Equipment RequiredVoltage Mode Operation Check Power on CheckCurrent Mode Operation Check Load Wiring Wire Size Maximum Current aInstallation Load Connections Installation Fastening the Output Wires 6000 Watt Low and Medium Voltage Multiple LoadsOutput Strain Relief/Cover Installation 11Output for 12000 Watt units High Voltage Remote Sensing Powering on Supply OperationOperation Power Supply Operating StatesPowering OFF Power Supply Do This You Will SeePower Supply Regulation Modes Remote Control Modes This output can be changed while the output is OFF Front Panel ControlsLCL/RMT, OUT ON/OFF, VOLTAGE, and Current keys Operation Operation Step # Do This You Will See Power Supply OperationThis saves the setting and enables New voltage setpointPress 8 times This saves the value and enablesNew power setpoint Turn Output On or Off Set Output ProtectionOperation To set the Over-Voltage Protection This setting is saved and the displayReturns to its default operating mode Use the Voltage knob, the numericTo set the Over-Current Protection These 2 extra steps are shown in the following exampleTo set the Under-Voltage Protection If trip? NUse both the Current and Voltage To set the Over-Power ProtectionTo set the Under-Current Protection Knobs, or the numeric keypad, orTo set the Under-Power Protection UPP SET ####WSet Shutdown Recovery for AC Off To set Fold ProtectionTimes To set both OTP and AC Off to Auto-RecoveryOTP is set to Auto Recovery ACO AutoRecov3Possible alarms are Toggle To shift from local to remote controlShutdown vs Protection Alarm Local/RemoteRS-232 Select Remote Control SourceTo change the remote control source Configure Remote Control Source Remote Control Prompt Configuration Settings SourceTo create and save a user setting Set #####A SettingsSet #####V Set 1 unusedTo retrieve a setting using Recall To restore the last settingTo select Auto Sequence To select a stored user settingTo select a factory setting Settings Affected by Recall Feature Factory Preset ValueMessages have been read Cleared To read and clear error messagesPress repeatedly until all None To access and work with the User Lines menu optionLine to configure To select which Aux line BConfigure Power on Settings Aux line B has been selected to be configuredTo configure Aux line B Enter to select, or Default display for the selected To select Factory PresetFactory Preset Operating modeUser Setting To select User SettingTo select Last Setting Last SettingAuto Sequence Sequence sequenceAuto-Sequence Auto SeqSequence To program a sequence Setting step advance by time Keys to select the Wait for Trig Option Setting step advance by triggerUse the scroll Deleting a This option allows you to delete an entire sequenceTo delete a sequence SequenceTimes or Editing a Sequence StepTo edit a step in a programmed sequence Edit StepStep # Inserting a Sequence StepTo insert a step into a programmed sequence Insert StepStep ## Deleted Deleting a Sequence StepTo delete a step in a programmed sequence Step ##Set Repeat # Editing Repeat Times SequenceTo edit the sequence’s repeat times Run OnceTrig Source To edit the sequence’s trigger sourceUsing Auto SequencingEditing Trigger Source of a Sequence Trig From ManVoltage operates as RUN/PAUSE Current operates as Trigger To run an auto sequence programTo lock out both knobs Voltage knob is locked out This setting is saved, and the displayTo lock out only the Voltage knob Current knob is not locked outTo set the voltage limits To set the current limits High #####W To set the power limitPower Limit Use the Voltage and Current knobsTo set the slew rate Time Default DisplayTo access and work with the View Model Information option XantrexRemote Operation Ieee 488.2 common commands that are supported are Remote OperationMaking Connections for Remote Control View of Remote Interface ConnectionsPin Connections User Line PinsRemote Analog Operation Pin # Function Input/OutputSchematic For User Line Interface Analog Programming PinsFront Panel First, configure the analog programming linesRemote Interlock Using a Contact Closure To select the voltage level Where Is the 0-5V range, and 10 is the 0-10V rangeTo put the unit into remote control Select desired option112 Pin # Multichannel Operation 6000 Watt onlyCANbus To receive and execute commands Connections for Multichannel Operation UsingChanging REM/LCL modes and calibration MultichannelSTATOPERRCONCOND? Specifications Will set all units in a multichannel string to 10.0First set the RS-232 parameters Configuration Front PanelRS-232 Operation Pin # FunctionSet the band rate Next, select RS-232 as the remote control interfaceSelect RS-232 to be the remote control source Select flow controlGpib Pins Gpib OperationFirst set the Gpib parameters Next, select Gpib as the remote control interfaceGpib setting is saved Select GpibTo select Gpib as the remote control source To set up Gpib control parametersWhere Gpib address may be in the range 1 to To check the current user setting Scpi Commands for Digital InterfacesTo power on factory settings Response should be PRES, which stands for PRESetTo check the setting To power on the last stored settingTo power on user setting #1 To reset to user setting #1To reset the unit Power onTo change the power on at output state Table belowFeatures Affected by Reset *RST Command Feature Reset State *RSTTo save default settings To store save settingsTo recall settings To recall last settingsChange Remote/Local Control Power Supply Program V,I,P ScpiTo check ranges To check a triggered setpointTo set limits Configure V PProtection Limits To check if the Over-Power Protection was tripped To set the Over-Power Protection levelTo check the Over-Power Protection level To set the Under-Power Protection levelTo set the fold delay Configure Other Protection MechanismsTo set the fold mode Fold ProtectionTo query if AC Off has tripped Over Temperature ProtectionTo query if OTP has tripped AC Off ProtectionEvent View Power Supply Output Configure Auxiliary Status LinesClear To set the polarity of the auxiliary status lines To set up Auxiliary line BRead Error To read from the error queue To check the state of the lineTo program triggers TRIGgerSOURce Busextimmnone WhereEditing Editing the Sequence Setting Sequence RepetitionsProgramming Select Sequence to Program Editing Step Parameters You can also use the following to delete all sequencesSelecting a Trigger Source Deleting SequencesTrigger Auto Sequence OperationRunning Skipping a StepVoltslewstep 1, Voltslewint 100ms May return Xantrex, XDC 60-100, 100000, 3.000/0/0/0000 Option Identification QueryStatus Registers OPERation Status Register Enable RegisterTransition Filters Operation Status Registers STATusOPERationREGulatingBit Bit Weight Bit Name Description OPERation Status RegisterBit REGulating Sub-RegisterSHUTdown Sub-Register Bit Name Description12 Protection SHUTdown Sub-Register Remote CONtrol Sub-RegisterProtection SHUTdown Sub-Register Current SHare Sub-Register QUEStionable Status Register Questionable Status Registers 15 QUEStionable Status Register TimeCURRent Sub-Register POWer Sub-RegisterVOLTage Sub-Register Standard Event Status Register TEMPerature Sub-Register19 TEMPerature Sub-Register Ieee 488.2 Status Register and Status ByteCondition. See Execution Error List on Been lost. See Query Error List onDevice-Specific Error List on See Command Error List on21 Status Byte Summary Register Error/Event Queue ERRStatus Byte RegisterMessage Available MAV Request Service RQSQuestionable Status Register Summary QSR Standard Event Status Summary ESBScpi Status Commands CommandsPreset Status 22 Preset Values of User Configurable RegistersIeee 488.2 Status and Event Commands Scpi equivalent for multichannel useCommand *SRE Service-Request-Enable, *SRE? Command *OPC, *OPC? SYSTemchannelPOSClear ONOFF01 SYSTemchannelPOSClear?Scpi command STATuschannelOPERationEVENt? Scpi commandOperation Status Register Commands Scpi command STATuschannelOPERationCONDition?Regulating Sub-Register Commands STATuschannelOPERationREGulatingCONDition?Shutdown Sub-Register Commands STATuschannelOPERationSHUTdownPTRansition?STATuschannelOPERationSHUTdownPROTectionENABle? Protection Shutdown Sub-Register CommandsRemote Control Sub-Register Commands STATuschannelOPERationRCONtrolCONDition?Current Share Sub-Register Commands STATuschannelOPERationCSHareCONDition?STATuschannelQUEStionableENABle? Questionable Status Register CommandsVoltage Sub-Register Commands STATuschannelQUEStionableVOLTageCONDition?Current Sub-Register Commands STATuschannelQUEStionableCURRentCONDition?STATuschannelQUEStionablePOWerENABle? Power Sub-Register CommandsTemperature Event Sub-Register is read and then cleared Temperature Sub-Register Commands172 Current Sharing 6000 Watt only Current Sharing 6000 Watt only Configure Current ShareNo sharing Press 7 timesSetup Current Sharing Network Operation 177 178 Entering Calibration Mode Appendix A. CalibrationFront Panel To access calibration mode via the front panel You are back in the Calibration menu. Output V Cal Output Cal Change CodeCode #### Setup and Equipment Output Current Front Panel Calibration ProcedurePower supply will set the output voltage to 90% Output VoltagePower supply will set the output to 90% Analog Programming Interface RangeAnalog Programming Interface Voltage Readback Calibration Analog Programming Interface Current Programming CalibrationEnter the voltage read from the external DVM. Press Enter Analog Programming Interface Current Readback CalibrationSet the output voltage to 90% by sending the command Remote Interface Calibration ProcedureSet the output voltage to 10% by sending the command Set the output current to 10% by sending the commandSet the output current to 90% by sending the command CALANAL5VPROGVOLTLEV MAXCALANAL5VREADVOLTLEV MIN CALANAL5VPROGCURRLEV MAX CALANAL10V Restore? Y Exit calibration modeRestore Factory Calibration Output V CalAppendix B. Scpi Command Reference Codes and StandardsIEEE-488.2/SCPI Syntax and Style Scpi Command HierarchyScpi Command Reference Parameters Units of Measure and MultipliersCALibrationCURRentLEVel currentMINMAX Using Scpi CommandsIs the same as typing OPC *PSC Off *TRG Using Minimum Maximum QueriesCALCURRentLEVel currentMINMAX Calstat on Parameter TypesVoltprot voltageMAXMIN Tables Scpi Command SummaryNotations Table B.1IEEE 488.2 Commands Scpi CommandTable B.2Readback Commands 200Table B.3Commands for Output Control Table B.4Commands for Current Share 6000 W only 202Table B.5Commands for Calibration Table B.6Command to Clear all Protection MechanismsTable B.9System Commands Table B.7Commands for Fold ProtectionTable B.8Commands for Triggering Table B.10Status Commands 206 207 208 Table B.13Output State Table B.11Protection CommandsTable B.12User Lines Table B.14Auto Sequence Commands PROGramchannelSELectedSTEPNEXT211 Table B.15Legacy Commands Legacy CommandExpressions Expression DetailsExpressions Appendix C. Error Messages Error Messages Command Error ListExecution Error List Errorcode Error Message DescriptionExecution Error List Device-Specific Error List Error Error Message Description CodeOperation Complete Event Query Error ListUser Request Event Analog Programming Interface Error codes Front Panel Error CodesCPU Error Codes Auto Sequencing Error CodesCANbus Error Codes Multichannel Error CodesCurrent Share Error Codes Address Range Service Request and PollingMessage Terminators AddressInterface Ieee 488.1 Section Protocol SpecificationsControl Functions Function Mnemonic Description Functions SubsetPerformance Specifications Electrical SpecificationsMechanical Specifications Driver Ieee 488.2 SectionPerformance Specifications Appendix E. Specifications and Characteristics Electrical Specifications-Summary Specifications and Characteristics229 Models 80-75 100-60 150-40 300-20 600-10 231 Models 10-1200 20-600 30-400 40-300 60-200 233 Models 80-150 100-120 150-80 300-40 600-20 235 Arms 6000 Watt AC Line Input SpecificationsAC Line Input Voltage Operating Ranges Arms 12000 WattOutput Performance Specifications 103% of maximum rated voltageProgramming Accuracy1 Typical Programming ResolutionTypical Measurement Resolution Readback AccuracyMinute Drift1 Hour Drift Temperature Stability2Temperature Coefficients Analog Programming InterfaceFor a programmed 95% to 5% step in output voltage Typical 31 kHz 62 kHz output rippleTo 95% step in output voltage Maximum Within regulation envelopeMaximum deviation as a percentage of rated output voltage Minimum 3.8 V for each line, 5 V typicalSpecification Environmental SpecificationHumidity Specification International ApprovalsMechanical Specification Figure E.1 Power Supply Dimensions 6000 Watt unitFigure E.2 Power Supply Dimensions 12000 Watt unit Index Gpib 247 248 249 250 Page Xantrex Technology Inc