CALANAL5VPROGVOLTLEV MAX | Xantrex Technology XDC manual

Calibration

Remote Interface Calibration Procedure

Analog

Programming

Interface 0-5V

Range

3.Enter current data

Enter the current read from the external DVM via the shunt. CAL:OUTP:CURR:DATA <current>

4.Maximum calibration level

Set the output current to 90% by sending the command:

CAL:OUTP:CURR:LEV MAX

5.Enter current data

Enter the current read from the shunt via the external DVM. CAL:OUTP:CURR:DATA <current>

6.Power supply calculates and stores calibration constants.

To set up to calibrate the analog programming interface, you will need a DC power source capable of outputting 0 to 5V and a DVM.

Table 4.2 “Analog Programming Pins”

Analog Programming Interface Voltage Programming Calibration

1.Connect the power source across the voltage programming lines, Pins B3 and B1(GND). Attach a DVM across the voltage programming lines as well.

2.Minimum calibration level

Set the input to the programming lines to approximately 0.5V (10% of full scale).

Set the power supply to receive 5V analog voltage programming calibration data with the command:

CAL:ANAL:5V:PROG:VOLT:LEV MIN

3.Enter voltage data

Enter the voltage at the voltage programming lines, read from the external DVM. CAL:ANAL:5V:PROG:VOLT:DATA <voltage>

4.Maximum calibration level

Set the input to the programming lines to approximately 4.5V (90% of full scale).

Set the power supply to receive 5V analog voltage programming calibration data with the command:

CAL:ANAL:5V:PROG:VOLT:LEV MAX

188	Operating Manual for XDC Series Power Supply

Image 190

Xantrex Technology XDC manual Set the output current to 90% by sending the command, CALANAL5VPROGVOLTLEV MAX

Contents

Operating Manual Page Operating Manual for What will Xantrex do? How do you get service?What does this warranty cover and how long does it last? Phone 604 422 Toll Free North America 800 667 Fax 604 421 What does this warranty not cover? Disclaimer Product Release Release 3.0 Information About Your Power SupplyModel Number Serial Number Purchased From Purchase Date Power Supply Safety Symbols Used in This Manual FCC Part 15 Radio Frequency Devices Class a Limits Approvals CE MarkCSA C22.2 No Unit complies with Canadian EMC requirements of ICES-001 About This Manual Who Should Use This Manual Navigation Sections Revisions About This Manual Contents Contents Operation Contents Remote Operation Current Sharing 6000 Watt only Appendix A. Calibration Appendix B. Scpi Command Reference Appendix C. Error Messages Appendix D. Gpib Appendix E. Specifications and CharacteristicsIndex List of Tables List of Tables List of Figures List of Figures About The XDC Power Supply Overview Front Panel About The XDC Power SupplyFront Panel 6000 Watt Front Panel 12000 Watt Keypad About The XDC Power Supply Key Functions Special Key Functions Menu Function Front Panel Display DisplayStatus Annunciators Front Panel Display, Status Annunciators Status Annunciators Rear Panel Rear Panel 6000 Watt low and medium output shown Overview of Operation About The XDC Power Supply Basic Setup Procedure Initial Inspection, Cleaning, and PackagingInspection Returning Power Supplies to the Manufacturer Packaging for Shipping or Storage Typical Box Label for Storage Location, Mounting, and Ventilation To install the power supply in an equipment rackRack Mounting Unpacking the Power Supply 6000 Watt shown Installation AC Input Power AC Input Connector for 6000 Watt units AC Wire Specification for 6000 Watt units AC Wire Input Connection For 6000 WAC Input Voltage Range Wire Attaching the AC Input Wires for 6000 Watt units AC Wire Input Connection for 12000 W Attaching the AC Input Wires for 12000 Watt units Basic Checks or Self-Tests Equipment Required Voltage Mode Operation Check Power on Check Current Mode Operation Check Load Wiring Wire Size Maximum Current a Installation Load Connections Installation Fastening the Output Wires 6000 Watt Low and Medium Voltage Multiple Loads Output Strain Relief/Cover Installation 11Output for 12000 Watt units High Voltage Remote Sensing Powering on Supply Operation Operation Power Supply Operating StatesPowering OFF Power Supply Do This You Will See Power Supply Regulation Modes Remote Control Modes LCL/RMT, OUT ON/OFF, VOLTAGE, and Current keys Front Panel ControlsThis output can be changed while the output is OFF Operation Operation Step # Do This You Will See Power Supply OperationThis saves the setting and enables New voltage setpoint Press 8 times This saves the value and enablesNew power setpoint Turn Output On or Off Set Output Protection Operation To set the Over-Voltage Protection This setting is saved and the displayReturns to its default operating mode Use the Voltage knob, the numeric To set the Over-Current Protection These 2 extra steps are shown in the following exampleTo set the Under-Voltage Protection If trip? N Use both the Current and Voltage To set the Over-Power ProtectionTo set the Under-Current Protection Knobs, or the numeric keypad, or To set the Under-Power Protection UPP SET ####W Set Shutdown Recovery for AC Off To set Fold Protection Times To set both OTP and AC Off to Auto-RecoveryOTP is set to Auto Recovery ACO AutoRecov3 Possible alarms are Toggle To shift from local to remote controlShutdown vs Protection Alarm Local/Remote To change the remote control source Select Remote Control SourceRS-232 Configure Remote Control Source Remote Control Prompt Configuration Settings Source To create and save a user setting Set #####A SettingsSet #####V Set 1 unused To retrieve a setting using Recall To restore the last setting To select a factory setting To select a stored user settingTo select Auto Sequence Settings Affected by Recall Feature Factory Preset Value Press repeatedly until all To read and clear error messagesMessages have been read Cleared None To access and work with the User Lines menu optionLine to configure To select which Aux line B To configure Aux line B Aux line B has been selected to be configuredConfigure Power on Settings Enter to select, or Default display for the selected To select Factory PresetFactory Preset Operating mode User Setting To select User SettingTo select Last Setting Last Setting Auto Sequence Sequence sequenceAuto-Sequence Auto Seq Sequence To program a sequence Setting step advance by time Use the scroll Setting step advance by triggerKeys to select the Wait for Trig Option Deleting a This option allows you to delete an entire sequenceTo delete a sequence Sequence Times or Editing a Sequence StepTo edit a step in a programmed sequence Edit Step Step # Inserting a Sequence StepTo insert a step into a programmed sequence Insert Step Step ## Deleted Deleting a Sequence StepTo delete a step in a programmed sequence Step ## Set Repeat # Editing Repeat Times SequenceTo edit the sequence’s repeat times Run Once Trig Source To edit the sequence’s trigger sourceUsing Auto SequencingEditing Trigger Source of a Sequence Trig From Man Voltage operates as RUN/PAUSE Current operates as Trigger To run an auto sequence program To lock out both knobs Voltage knob is locked out This setting is saved, and the displayTo lock out only the Voltage knob Current knob is not locked out To set the voltage limits To set the current limits High #####W To set the power limitPower Limit Use the Voltage and Current knobs To set the slew rate Time Default DisplayTo access and work with the View Model Information option Xantrex Remote Operation Ieee 488.2 common commands that are supported are Remote Operation Making Connections for Remote Control View of Remote Interface Connections Pin Connections User Line PinsRemote Analog Operation Pin # Function Input/Output Schematic For User Line Interface Analog Programming Pins Remote Interlock Using a Contact Closure First, configure the analog programming linesFront Panel To select the voltage level Where Is the 0-5V range, and 10 is the 0-10V rangeTo put the unit into remote control Select desired option 112 CANbus Multichannel Operation 6000 Watt onlyPin # To receive and execute commands Connections for Multichannel Operation UsingChanging REM/LCL modes and calibration Multichannel STATOPERRCONCOND? Specifications Will set all units in a multichannel string to 10.0 First set the RS-232 parameters Configuration Front PanelRS-232 Operation Pin # Function Set the band rate Next, select RS-232 as the remote control interfaceSelect RS-232 to be the remote control source Select flow control Gpib Pins Gpib Operation First set the Gpib parameters Next, select Gpib as the remote control interfaceGpib setting is saved Select Gpib Where Gpib address may be in the range 1 to To set up Gpib control parametersTo select Gpib as the remote control source To check the current user setting Scpi Commands for Digital InterfacesTo power on factory settings Response should be PRES, which stands for PRESet To check the setting To power on the last stored settingTo power on user setting #1 To reset to user setting #1 To reset the unit Power onTo change the power on at output state Table below Features Affected by Reset *RST Command Feature Reset State *RST To save default settings To store save settingsTo recall settings To recall last settings Change Remote/Local Control Power Supply Program V,I,P Scpi To set limits To check a triggered setpointTo check ranges Configure V PProtection Limits To check if the Over-Power Protection was tripped To set the Over-Power Protection levelTo check the Over-Power Protection level To set the Under-Power Protection level To set the fold delay Configure Other Protection MechanismsTo set the fold mode Fold Protection To query if AC Off has tripped Over Temperature ProtectionTo query if OTP has tripped AC Off Protection Clear View Power Supply Output Configure Auxiliary Status LinesEvent To set the polarity of the auxiliary status lines To set up Auxiliary line BRead Error To read from the error queue To check the state of the line To program triggers TRIGgerSOURce Busextimmnone Where Editing Programming Select Sequence to Program Setting Sequence RepetitionsEditing the Sequence Editing Step Parameters You can also use the following to delete all sequencesSelecting a Trigger Source Deleting Sequences Trigger Auto Sequence OperationRunning Skipping a Step Voltslewstep 1, Voltslewint 100ms Status Registers Option Identification QueryMay return Xantrex, XDC 60-100, 100000, 3.000/0/0/0000 Transition Filters Enable RegisterOPERation Status Register Operation Status Registers STATusOPERationREGulating Bit Bit Weight Bit Name Description OPERation Status Register Bit REGulating Sub-RegisterSHUTdown Sub-Register Bit Name Description Protection SHUTdown Sub-Register Remote CONtrol Sub-Register12 Protection SHUTdown Sub-Register Current SHare Sub-Register QUEStionable Status Register Questionable Status Registers 15 QUEStionable Status Register Time VOLTage Sub-Register POWer Sub-RegisterCURRent Sub-Register Standard Event Status Register TEMPerature Sub-Register19 TEMPerature Sub-Register Ieee 488.2 Status Register and Status Byte Condition. See Execution Error List on Been lost. See Query Error List onDevice-Specific Error List on See Command Error List on 21 Status Byte Summary Register Error/Event Queue ERRStatus Byte Register Message Available MAV Request Service RQSQuestionable Status Register Summary QSR Standard Event Status Summary ESB Scpi Status Commands CommandsPreset Status 22 Preset Values of User Configurable Registers Ieee 488.2 Status and Event Commands Scpi equivalent for multichannel use Command *SRE Service-Request-Enable, *SRE? Command *OPC, *OPC? SYSTemchannelPOSClear ONOFF01 SYSTemchannelPOSClear? Scpi command STATuschannelOPERationEVENt? Scpi commandOperation Status Register Commands Scpi command STATuschannelOPERationCONDition? Regulating Sub-Register Commands STATuschannelOPERationREGulatingCONDition? Shutdown Sub-Register Commands STATuschannelOPERationSHUTdownPTRansition? STATuschannelOPERationSHUTdownPROTectionENABle? Protection Shutdown Sub-Register Commands Remote Control Sub-Register Commands STATuschannelOPERationRCONtrolCONDition? Current Share Sub-Register Commands STATuschannelOPERationCSHareCONDition? STATuschannelQUEStionableENABle? Questionable Status Register Commands Voltage Sub-Register Commands STATuschannelQUEStionableVOLTageCONDition? Current Sub-Register Commands STATuschannelQUEStionableCURRentCONDition? STATuschannelQUEStionablePOWerENABle? Power Sub-Register Commands Temperature Event Sub-Register is read and then cleared Temperature Sub-Register Commands 172 Current Sharing 6000 Watt only Current Sharing 6000 Watt only Configure Current ShareNo sharing Press 7 times Setup Current Sharing Network Operation 177 178 Entering Calibration Mode Appendix A. Calibration Front Panel To access calibration mode via the front panel Code #### Output Cal Change CodeYou are back in the Calibration menu. Output V Cal Setup and Equipment Output Current Front Panel Calibration ProcedurePower supply will set the output voltage to 90% Output Voltage Power supply will set the output to 90% Analog Programming Interface Range Analog Programming Interface Voltage Readback Calibration Analog Programming Interface Current Programming Calibration Enter the voltage read from the external DVM. Press Enter Analog Programming Interface Current Readback Calibration Set the output voltage to 90% by sending the command Remote Interface Calibration ProcedureSet the output voltage to 10% by sending the command Set the output current to 10% by sending the command Set the output current to 90% by sending the command CALANAL5VPROGVOLTLEV MAX CALANAL5VREADVOLTLEV MIN CALANAL5VPROGCURRLEV MAX CALANAL10V Restore? Y Exit calibration modeRestore Factory Calibration Output V Cal Appendix B. Scpi Command Reference Codes and Standards IEEE-488.2/SCPI Syntax and Style Scpi Command HierarchyScpi Command Reference Parameters Units of Measure and Multipliers Is the same as typing Using Scpi CommandsCALibrationCURRentLEVel currentMINMAX CALCURRentLEVel currentMINMAX Using Minimum Maximum QueriesOPC *PSC Off *TRG Voltprot voltageMAXMIN Parameter TypesCalstat on Notations Scpi Command SummaryTables Table B.1IEEE 488.2 Commands Scpi Command Table B.2Readback Commands 200 Table B.3Commands for Output Control Table B.4Commands for Current Share 6000 W only 202 Table B.5Commands for Calibration Table B.6Command to Clear all Protection Mechanisms Table B.8Commands for Triggering Table B.7Commands for Fold ProtectionTable B.9System Commands Table B.10Status Commands 206 207 208 Table B.12User Lines Table B.11Protection CommandsTable B.13Output State Table B.14Auto Sequence Commands PROGramchannelSELectedSTEPNEXT 211 Table B.15Legacy Commands Legacy Command Expressions Expression Details Expressions Appendix C. Error Messages Error Messages Command Error ListExecution Error List Errorcode Error Message Description Execution Error List Device-Specific Error List Error Error Message Description Code User Request Event Query Error ListOperation Complete Event Analog Programming Interface Error codes Front Panel Error CodesCPU Error Codes Auto Sequencing Error Codes CANbus Error Codes Multichannel Error Codes Current Share Error Codes Address Range Service Request and PollingMessage Terminators Address Interface Ieee 488.1 Section Protocol SpecificationsControl Functions Function Mnemonic Description Functions Subset Performance Specifications Electrical SpecificationsMechanical Specifications Driver Ieee 488.2 Section Performance Specifications Appendix E. Specifications and Characteristics Electrical Specifications-Summary Specifications and Characteristics 229 Models 80-75 100-60 150-40 300-20 600-10 231 Models 10-1200 20-600 30-400 40-300 60-200 233 Models 80-150 100-120 150-80 300-40 600-20 235 Arms 6000 Watt AC Line Input SpecificationsAC Line Input Voltage Operating Ranges Arms 12000 Watt Output Performance Specifications 103% of maximum rated voltage Programming Accuracy1 Typical Programming ResolutionTypical Measurement Resolution Readback Accuracy Minute Drift1 Hour Drift Temperature Stability2Temperature Coefficients Analog Programming Interface For a programmed 95% to 5% step in output voltage Typical 31 kHz 62 kHz output rippleTo 95% step in output voltage Maximum Within regulation envelope Maximum deviation as a percentage of rated output voltage Minimum 3.8 V for each line, 5 V typical Specification Environmental SpecificationHumidity Specification International Approvals Mechanical Specification Figure E.1 Power Supply Dimensions 6000 Watt unit Figure E.2 Power Supply Dimensions 12000 Watt unit Index Gpib 247 248 249 250 Page Xantrex Technology Inc