To set the Under-Current Protection level | Xantrex Technology XDC

Remote Operation

SCPI Commands for Digital Interfaces

Under-Current Protection

To set the Under-Current Protection level:

SOUR:CURR:PROT:UND <current>

SOUR:CURR:PROT:UND:STAT <on-off-state>

The first UCP protection command sets the protection level. The second command lets you choose a warning alarm only [OFF] or shut down with an alarm [ON] if the protection level is exceeded.

To check the Under-Current Protection level:

SOUR:CURR:PROT?

To check if the Under-Current Protection was tripped:

SOUR:CURR:PROT:TRIP?

Over-Power Protection

To set the Over-Power Protection level:

SOUR:POW:PROT <wattage>

SOUR:POW:PROT:STAT <on-off-state>

The first OPP protection command sets the protection level. The second command lets you choose a warning alarm only [OFF] or shut down with an alarm [ON] if the protection level is exceeded.

To check the Over-Power Protection level:

SOUR:POW:PROT?

To check if the Over-Power Protection was tripped:

SOUR:POW:PROT:TRIP?

Under-Power Protection

To set the Under-Power Protection level:

SOUR:POW:PROT:UND <wattage>

SOUR:POW:PROT:UND:STAT <on-off-state>

The first UPP protection command sets the protection level. The second command lets you choose a warning alarm only [OFF] or shut down with an alarm [ON] if the protection level is exceeded.

To check the Under-Power Protection level:

SOUR:POW:PROT?

To check if the Under-Power Protection was tripped:

SOUR:POW:PROT:TRIP?

Release 3.0

131

Image 133

Xantrex Technology XDC manual To set the Under-Current Protection level, To check the Under-Current Protection level

Contents

Operating Manual Page Operating Manual for What does this warranty cover and how long does it last? How do you get service?What will Xantrex do? Phone 604 422 Toll Free North America 800 667 Fax 604 421 What does this warranty not cover? Disclaimer Product Release Release 3.0 Information About Your Power SupplyModel Number Serial Number Purchased From Purchase Date Power Supply Safety Manual Symbols Used in This CSA C22.2 No Approvals CE MarkFCC Part 15 Radio Frequency Devices Class a Limits Unit complies with Canadian EMC requirements of ICES-001 Who Should Use This Manual Navigation Sections About This Manual About This Manual Revisions Contents Operation Contents Remote Operation Contents Appendix A. Calibration Current Sharing 6000 Watt only Appendix C. Error Messages Appendix B. Scpi Command Reference Appendix D. Gpib Appendix E. Specifications and CharacteristicsIndex List of Tables List of Tables List of Figures List of Figures Overview About The XDC Power Supply Front Panel About The XDC Power SupplyFront Panel 6000 Watt Front Panel 12000 Watt Keypad About The XDC Power Supply Special Key Functions Key Functions Menu Function Status Annunciators DisplayFront Panel Display Front Panel Display, Status Annunciators Status Annunciators Rear Panel 6000 Watt low and medium output shown Rear Panel Overview of Operation About The XDC Power Supply Basic Setup Procedure Initial Inspection, Cleaning, and PackagingInspection Returning Power Supplies to the Manufacturer Typical Box Label for Storage Packaging for Shipping or Storage Location, Mounting, and Ventilation To install the power supply in an equipment rackRack Mounting Unpacking the Power Supply 6000 Watt shown Installation AC Input Connector for 6000 Watt units AC Input Power AC Wire Specification for 6000 Watt units AC Wire Input Connection For 6000 WAC Input Voltage Range Wire Attaching the AC Input Wires for 6000 Watt units AC Wire Input Connection for 12000 W Attaching the AC Input Wires for 12000 Watt units Equipment Required Basic Checks or Self-Tests Power on Check Voltage Mode Operation Check Current Mode Operation Check Wire Size Maximum Current a Load Wiring Installation Load Connections Installation Multiple Loads Fastening the Output Wires 6000 Watt Low and Medium Voltage Output Strain Relief/Cover Installation 11Output for 12000 Watt units High Voltage Remote Sensing Operation Powering on Supply Powering OFF Power Supply Power Supply Operating StatesOperation Do This You Will See Power Supply Regulation Modes Remote Control Modes LCL/RMT, OUT ON/OFF, VOLTAGE, and Current keys Front Panel ControlsThis output can be changed while the output is OFF Operation Operation This saves the setting and enables Power Supply OperationStep # Do This You Will See New voltage setpoint New power setpoint This saves the value and enablesPress 8 times Turn Output On or Off Set Output Protection Operation Returns to its default operating mode This setting is saved and the displayTo set the Over-Voltage Protection Use the Voltage knob, the numeric To set the Under-Voltage Protection These 2 extra steps are shown in the following exampleTo set the Over-Current Protection If trip? N To set the Under-Current Protection To set the Over-Power ProtectionUse both the Current and Voltage Knobs, or the numeric keypad, or UPP SET ####W To set the Under-Power Protection To set Fold Protection Set Shutdown Recovery for AC Off OTP is set to Auto Recovery To set both OTP and AC Off to Auto-RecoveryTimes ACO AutoRecov3 Possible alarms are Shutdown vs Protection Alarm To shift from local to remote controlToggle Local/Remote To change the remote control source Select Remote Control SourceRS-232 Remote Control Prompt Configuration Settings Source Configure Remote Control Source To create and save a user setting Set #####V SettingsSet #####A Set 1 unused To restore the last setting To retrieve a setting using Recall To select a factory setting To select a stored user settingTo select Auto Sequence Feature Factory Preset Value Settings Affected by Recall Press repeatedly until all To read and clear error messagesMessages have been read Cleared Line to configure To access and work with the User Lines menu optionNone To select which Aux line B To configure Aux line B Aux line B has been selected to be configuredConfigure Power on Settings Factory Preset To select Factory PresetEnter to select, or Default display for the selected Operating mode To select Last Setting To select User SettingUser Setting Last Setting Auto-Sequence Sequence sequenceAuto Sequence Auto Seq Sequence To program a sequence Setting step advance by time Use the scroll Setting step advance by triggerKeys to select the Wait for Trig Option To delete a sequence This option allows you to delete an entire sequenceDeleting a Sequence To edit a step in a programmed sequence Editing a Sequence StepTimes or Edit Step To insert a step into a programmed sequence Inserting a Sequence StepStep # Insert Step To delete a step in a programmed sequence Deleting a Sequence StepStep ## Deleted Step ## To edit the sequence’s repeat times Editing Repeat Times SequenceSet Repeat # Run Once Editing Trigger Source of a Sequence To edit the sequence’s trigger sourceUsing Auto SequencingTrig Source Trig From Man To run an auto sequence program Voltage operates as RUN/PAUSE Current operates as Trigger To lock out both knobs To lock out only the Voltage knob This setting is saved, and the displayVoltage knob is locked out Current knob is not locked out To set the voltage limits To set the current limits Power Limit To set the power limitHigh #####W Use the Voltage and Current knobs To set the slew rate To access and work with the View Model Information option Default DisplayTime Xantrex Remote Operation Remote Operation Ieee 488.2 common commands that are supported are View of Remote Interface Connections Making Connections for Remote Control Remote Analog Operation User Line PinsPin Connections Pin # Function Input/Output Analog Programming Pins Schematic For User Line Interface Remote Interlock Using a Contact Closure First, configure the analog programming linesFront Panel To put the unit into remote control Where Is the 0-5V range, and 10 is the 0-10V rangeTo select the voltage level Select desired option 112 CANbus Multichannel Operation 6000 Watt onlyPin # To receive and execute commands Changing REM/LCL modes and calibration UsingConnections for Multichannel Operation Multichannel STATOPERRCONCOND? Will set all units in a multichannel string to 10.0 Specifications RS-232 Operation Configuration Front PanelFirst set the RS-232 parameters Pin # Function Select RS-232 to be the remote control source Next, select RS-232 as the remote control interfaceSet the band rate Select flow control Gpib Operation Gpib Pins Gpib setting is saved Next, select Gpib as the remote control interfaceFirst set the Gpib parameters Select Gpib Where Gpib address may be in the range 1 to To set up Gpib control parametersTo select Gpib as the remote control source To power on factory settings Scpi Commands for Digital InterfacesTo check the current user setting Response should be PRES, which stands for PRESet To power on user setting #1 To power on the last stored settingTo check the setting To reset to user setting #1 To change the power on at output state Power onTo reset the unit Table below Feature Reset State *RST Features Affected by Reset *RST Command To recall settings To store save settingsTo save default settings To recall last settings Program V,I,P Scpi Change Remote/Local Control Power Supply To set limits To check a triggered setpointTo check ranges Configure V PProtection Limits To check the Over-Power Protection level To set the Over-Power Protection levelTo check if the Over-Power Protection was tripped To set the Under-Power Protection level To set the fold mode Configure Other Protection MechanismsTo set the fold delay Fold Protection To query if OTP has tripped Over Temperature ProtectionTo query if AC Off has tripped AC Off Protection Clear View Power Supply Output Configure Auxiliary Status LinesEvent Read Error To read from the error queue To set up Auxiliary line BTo set the polarity of the auxiliary status lines To check the state of the line TRIGgerSOURce Busextimmnone Where To program triggers Editing Programming Select Sequence to Program Setting Sequence RepetitionsEditing the Sequence Selecting a Trigger Source You can also use the following to delete all sequencesEditing Step Parameters Deleting Sequences Running Auto Sequence OperationTrigger Skipping a Step Voltslewstep 1, Voltslewint 100ms Status Registers Option Identification QueryMay return Xantrex, XDC 60-100, 100000, 3.000/0/0/0000 Transition Filters Enable RegisterOPERation Status Register STATusOPERationREGulating Operation Status Registers OPERation Status Register Bit Bit Weight Bit Name Description SHUTdown Sub-Register REGulating Sub-RegisterBit Bit Name Description Protection SHUTdown Sub-Register Remote CONtrol Sub-Register12 Protection SHUTdown Sub-Register Current SHare Sub-Register QUEStionable Status Register Questionable Status Registers Time 15 QUEStionable Status Register VOLTage Sub-Register POWer Sub-RegisterCURRent Sub-Register 19 TEMPerature Sub-Register TEMPerature Sub-RegisterStandard Event Status Register Ieee 488.2 Status Register and Status Byte Device-Specific Error List on Been lost. See Query Error List onCondition. See Execution Error List on See Command Error List on Status Byte Error/Event Queue ERR21 Status Byte Summary Register Register Questionable Status Register Summary QSR Request Service RQSMessage Available MAV Standard Event Status Summary ESB Preset Status CommandsScpi Status Commands 22 Preset Values of User Configurable Registers Scpi equivalent for multichannel use Ieee 488.2 Status and Event Commands Command *SRE Service-Request-Enable, *SRE? SYSTemchannelPOSClear ONOFF01 SYSTemchannelPOSClear? Command *OPC, *OPC? Operation Status Register Commands Scpi commandScpi command STATuschannelOPERationEVENt? Scpi command STATuschannelOPERationCONDition? STATuschannelOPERationREGulatingCONDition? Regulating Sub-Register Commands STATuschannelOPERationSHUTdownPTRansition? Shutdown Sub-Register Commands Protection Shutdown Sub-Register Commands STATuschannelOPERationSHUTdownPROTectionENABle? STATuschannelOPERationRCONtrolCONDition? Remote Control Sub-Register Commands STATuschannelOPERationCSHareCONDition? Current Share Sub-Register Commands Questionable Status Register Commands STATuschannelQUEStionableENABle? STATuschannelQUEStionableVOLTageCONDition? Voltage Sub-Register Commands STATuschannelQUEStionableCURRentCONDition? Current Sub-Register Commands Power Sub-Register Commands STATuschannelQUEStionablePOWerENABle? Temperature Sub-Register Commands Temperature Event Sub-Register is read and then cleared 172 Current Sharing 6000 Watt only No sharing Configure Current ShareCurrent Sharing 6000 Watt only Press 7 times Setup Current Sharing Network Operation 177 178 Appendix A. Calibration Entering Calibration Mode Front Panel To access calibration mode via the front panel Code #### Output Cal Change CodeYou are back in the Calibration menu. Output V Cal Setup and Equipment Power supply will set the output voltage to 90% Front Panel Calibration ProcedureOutput Current Output Voltage Analog Programming Interface Range Power supply will set the output to 90% Analog Programming Interface Current Programming Calibration Analog Programming Interface Voltage Readback Calibration Analog Programming Interface Current Readback Calibration Enter the voltage read from the external DVM. Press Enter Set the output voltage to 10% by sending the command Remote Interface Calibration ProcedureSet the output voltage to 90% by sending the command Set the output current to 10% by sending the command CALANAL5VPROGVOLTLEV MAX Set the output current to 90% by sending the command CALANAL5VREADVOLTLEV MIN CALANAL5VPROGCURRLEV MAX CALANAL10V Restore Factory Calibration Exit calibration modeRestore? Y Output V Cal Codes and Standards Appendix B. Scpi Command Reference Scpi Command Reference Scpi Command HierarchyIEEE-488.2/SCPI Syntax and Style Parameters Units of Measure and Multipliers Is the same as typing Using Scpi CommandsCALibrationCURRentLEVel currentMINMAX CALCURRentLEVel currentMINMAX Using Minimum Maximum QueriesOPC *PSC Off *TRG Voltprot voltageMAXMIN Parameter TypesCalstat on Notations Scpi Command SummaryTables Scpi Command Table B.1IEEE 488.2 Commands 200 Table B.2Readback Commands Table B.3Commands for Output Control 202 Table B.4Commands for Current Share 6000 W only Table B.6Command to Clear all Protection Mechanisms Table B.5Commands for Calibration Table B.8Commands for Triggering Table B.7Commands for Fold ProtectionTable B.9System Commands Table B.10Status Commands 206 207 208 Table B.12User Lines Table B.11Protection CommandsTable B.13Output State PROGramchannelSELectedSTEPNEXT Table B.14Auto Sequence Commands 211 Legacy Command Table B.15Legacy Commands Expression Details Expressions Expressions Appendix C. Error Messages Execution Error List Command Error ListError Messages Errorcode Error Message Description Execution Error List Error Error Message Description Code Device-Specific Error List User Request Event Query Error ListOperation Complete Event CPU Error Codes Front Panel Error CodesAnalog Programming Interface Error codes Auto Sequencing Error Codes Multichannel Error Codes CANbus Error Codes Current Share Error Codes Message Terminators Service Request and PollingAddress Range Address Control Functions Protocol SpecificationsInterface Ieee 488.1 Section Function Mnemonic Description Functions Subset Mechanical Specifications Electrical SpecificationsPerformance Specifications Driver Ieee 488.2 Section Performance Specifications Appendix E. Specifications and Characteristics Specifications and Characteristics Electrical Specifications-Summary 229 Models 80-75 100-60 150-40 300-20 600-10 231 Models 10-1200 20-600 30-400 40-300 60-200 233 Models 80-150 100-120 150-80 300-40 600-20 235 AC Line Input Voltage Operating Ranges AC Line Input SpecificationsArms 6000 Watt Arms 12000 Watt 103% of maximum rated voltage Output Performance Specifications Typical Measurement Resolution Typical Programming ResolutionProgramming Accuracy1 Readback Accuracy Temperature Coefficients Hour Drift Temperature Stability2Minute Drift1 Analog Programming Interface To 95% step in output voltage Typical 31 kHz 62 kHz output rippleFor a programmed 95% to 5% step in output voltage Maximum Within regulation envelope Minimum 3.8 V for each line, 5 V typical Maximum deviation as a percentage of rated output voltage Humidity Specification Environmental SpecificationSpecification International Approvals Figure E.1 Power Supply Dimensions 6000 Watt unit Mechanical Specification Figure E.2 Power Supply Dimensions 12000 Watt unit Index Gpib 247 248 249 250 Page Xantrex Technology Inc