STATuschannelOPERationREGulatingCONDition? | Xantrex Technology XDC

Remote Operation

SCPI Commands for Digital Interfaces

Regulating Sub-Register Commands

Query Regulating Event

SCPI command:

STATus[<channel>]:OPERation:REGulating[:EVENt]?

Query Regulating Condition

SCPI command:

STATus[<channel>]:OPERation:REGulating:CONDition?

Enable Regulating Sub-Register

SCPI command: STATus[<channel>]:OPERation:REGulating:ENABle <status-enable>

Query format:

STATus[<channel>]:OPERation:REGulating:ENABle?

Set Regulating Positive Transition Filter

SCPI command: STATus[<channel>]:OPERation:REGulating:PTRansition <status-enable>

Query format:

STATus[<channel>]:OPERation:REGulating:PTRansition?

Set Regulating Negative Transition Filter

SCPI command: STATus[<channel>]:OPERation:REGulating:NTRansition <status-enable>

Query format:

STATus[<channel>]:OPERation:REGulating:NTRansition?

162	Operating Manual for XDC Series Power Supply

Image 164

Xantrex Technology XDC manual STATuschannelOPERationREGulatingCONDition?, Regulating Sub-Register Commands

Contents

Operating Manual Page Operating Manual for How do you get service? What does this warranty cover and how long does it last?What will Xantrex do? Phone 604 422 Toll Free North America 800 667 Fax 604 421 What does this warranty not cover? Disclaimer Product Model Number Serial Number Purchased From Purchase Date Information About Your Power SupplyRelease Release 3.0 Power Supply Safety Symbols Used in This Manual Approvals CE Mark CSA C22.2 NoFCC Part 15 Radio Frequency Devices Class a Limits Unit complies with Canadian EMC requirements of ICES-001 About This Manual Who Should Use This Manual Navigation Sections Revisions About This Manual Contents Contents Operation Contents Remote Operation Current Sharing 6000 Watt only Appendix A. Calibration Appendix B. Scpi Command Reference Appendix C. Error Messages Index Appendix E. Specifications and CharacteristicsAppendix D. Gpib List of Tables List of Tables List of Figures List of Figures About The XDC Power Supply Overview Front Panel 6000 Watt About The XDC Power SupplyFront Panel Front Panel 12000 Watt Keypad About The XDC Power Supply Key Functions Special Key Functions Menu Function Display Status AnnunciatorsFront Panel Display Front Panel Display, Status Annunciators Status Annunciators Rear Panel Rear Panel 6000 Watt low and medium output shown Overview of Operation About The XDC Power Supply Basic Setup Procedure Inspection Inspection, Cleaning, and PackagingInitial Returning Power Supplies to the Manufacturer Packaging for Shipping or Storage Typical Box Label for Storage Rack Mounting To install the power supply in an equipment rackLocation, Mounting, and Ventilation Unpacking the Power Supply 6000 Watt shown Installation AC Input Power AC Input Connector for 6000 Watt units AC Input Voltage Range Wire AC Wire Input Connection For 6000 WAC Wire Specification for 6000 Watt units Attaching the AC Input Wires for 6000 Watt units AC Wire Input Connection for 12000 W Attaching the AC Input Wires for 12000 Watt units Basic Checks or Self-Tests Equipment Required Voltage Mode Operation Check Power on Check Current Mode Operation Check Load Wiring Wire Size Maximum Current a Installation Load Connections Installation Fastening the Output Wires 6000 Watt Low and Medium Voltage Multiple Loads Output Strain Relief/Cover Installation 11Output for 12000 Watt units High Voltage Remote Sensing Powering on Supply Operation Power Supply Operating States Powering OFF Power SupplyOperation Do This You Will See Power Supply Regulation Modes Remote Control Modes This output can be changed while the output is OFF Front Panel ControlsLCL/RMT, OUT ON/OFF, VOLTAGE, and Current keys Operation Operation Power Supply Operation This saves the setting and enablesStep # Do This You Will See New voltage setpoint This saves the value and enables New power setpointPress 8 times Turn Output On or Off Set Output Protection Operation This setting is saved and the display Returns to its default operating modeTo set the Over-Voltage Protection Use the Voltage knob, the numeric These 2 extra steps are shown in the following example To set the Under-Voltage ProtectionTo set the Over-Current Protection If trip? N To set the Over-Power Protection To set the Under-Current ProtectionUse both the Current and Voltage Knobs, or the numeric keypad, or To set the Under-Power Protection UPP SET ####W Set Shutdown Recovery for AC Off To set Fold Protection To set both OTP and AC Off to Auto-Recovery OTP is set to Auto RecoveryTimes ACO AutoRecov3 Possible alarms are To shift from local to remote control Shutdown vs Protection AlarmToggle Local/Remote RS-232 Select Remote Control SourceTo change the remote control source Configure Remote Control Source Remote Control Prompt Configuration Settings Source To create and save a user setting Settings Set #####VSet #####A Set 1 unused To retrieve a setting using Recall To restore the last setting To select Auto Sequence To select a stored user settingTo select a factory setting Settings Affected by Recall Feature Factory Preset Value Messages have been read Cleared To read and clear error messagesPress repeatedly until all To access and work with the User Lines menu option Line to configureNone To select which Aux line B Configure Power on Settings Aux line B has been selected to be configuredTo configure Aux line B To select Factory Preset Factory PresetEnter to select, or Default display for the selected Operating mode To select User Setting To select Last SettingUser Setting Last Setting Sequence sequence Auto-SequenceAuto Sequence Auto Seq Sequence To program a sequence Setting step advance by time Keys to select the Wait for Trig Option Setting step advance by triggerUse the scroll This option allows you to delete an entire sequence To delete a sequenceDeleting a Sequence Editing a Sequence Step To edit a step in a programmed sequenceTimes or Edit Step Inserting a Sequence Step To insert a step into a programmed sequenceStep # Insert Step Deleting a Sequence Step To delete a step in a programmed sequenceStep ## Deleted Step ## Editing Repeat Times Sequence To edit the sequence’s repeat timesSet Repeat # Run Once To edit the sequence’s trigger sourceUsing Auto Sequencing Editing Trigger Source of a SequenceTrig Source Trig From Man Voltage operates as RUN/PAUSE Current operates as Trigger To run an auto sequence program To lock out both knobs This setting is saved, and the display To lock out only the Voltage knobVoltage knob is locked out Current knob is not locked out To set the voltage limits To set the current limits To set the power limit Power LimitHigh #####W Use the Voltage and Current knobs To set the slew rate Default Display To access and work with the View Model Information optionTime Xantrex Remote Operation Ieee 488.2 common commands that are supported are Remote Operation Making Connections for Remote Control View of Remote Interface Connections User Line Pins Remote Analog OperationPin Connections Pin # Function Input/Output Schematic For User Line Interface Analog Programming Pins Front Panel First, configure the analog programming linesRemote Interlock Using a Contact Closure Where Is the 0-5V range, and 10 is the 0-10V range To put the unit into remote controlTo select the voltage level Select desired option 112 Pin # Multichannel Operation 6000 Watt onlyCANbus To receive and execute commands Using Changing REM/LCL modes and calibrationConnections for Multichannel Operation Multichannel STATOPERRCONCOND? Specifications Will set all units in a multichannel string to 10.0 Configuration Front Panel RS-232 OperationFirst set the RS-232 parameters Pin # Function Next, select RS-232 as the remote control interface Select RS-232 to be the remote control sourceSet the band rate Select flow control Gpib Pins Gpib Operation Next, select Gpib as the remote control interface Gpib setting is savedFirst set the Gpib parameters Select Gpib To select Gpib as the remote control source To set up Gpib control parametersWhere Gpib address may be in the range 1 to Scpi Commands for Digital Interfaces To power on factory settingsTo check the current user setting Response should be PRES, which stands for PRESet To power on the last stored setting To power on user setting #1To check the setting To reset to user setting #1 Power on To change the power on at output stateTo reset the unit Table below Features Affected by Reset *RST Command Feature Reset State *RST To store save settings To recall settingsTo save default settings To recall last settings Change Remote/Local Control Power Supply Program V,I,P Scpi To check ranges To check a triggered setpointTo set limits Configure V PProtection Limits To set the Over-Power Protection level To check the Over-Power Protection levelTo check if the Over-Power Protection was tripped To set the Under-Power Protection level Configure Other Protection Mechanisms To set the fold modeTo set the fold delay Fold Protection Over Temperature Protection To query if OTP has trippedTo query if AC Off has tripped AC Off Protection Event View Power Supply Output Configure Auxiliary Status LinesClear To set up Auxiliary line B Read Error To read from the error queueTo set the polarity of the auxiliary status lines To check the state of the line To program triggers TRIGgerSOURce Busextimmnone Where Editing Editing the Sequence Setting Sequence RepetitionsProgramming Select Sequence to Program You can also use the following to delete all sequences Selecting a Trigger SourceEditing Step Parameters Deleting Sequences Auto Sequence Operation RunningTrigger Skipping a Step Voltslewstep 1, Voltslewint 100ms May return Xantrex, XDC 60-100, 100000, 3.000/0/0/0000 Option Identification QueryStatus Registers OPERation Status Register Enable RegisterTransition Filters Operation Status Registers STATusOPERationREGulating Bit Bit Weight Bit Name Description OPERation Status Register REGulating Sub-Register SHUTdown Sub-RegisterBit Bit Name Description 12 Protection SHUTdown Sub-Register Remote CONtrol Sub-RegisterProtection SHUTdown Sub-Register Current SHare Sub-Register QUEStionable Status Register Questionable Status Registers 15 QUEStionable Status Register Time CURRent Sub-Register POWer Sub-RegisterVOLTage Sub-Register TEMPerature Sub-Register 19 TEMPerature Sub-RegisterStandard Event Status Register Ieee 488.2 Status Register and Status Byte Been lost. See Query Error List on Device-Specific Error List onCondition. See Execution Error List on See Command Error List on Error/Event Queue ERR Status Byte21 Status Byte Summary Register Register Request Service RQS Questionable Status Register Summary QSRMessage Available MAV Standard Event Status Summary ESB Commands Preset StatusScpi Status Commands 22 Preset Values of User Configurable Registers Ieee 488.2 Status and Event Commands Scpi equivalent for multichannel use Command *SRE Service-Request-Enable, *SRE? Command *OPC, *OPC? SYSTemchannelPOSClear ONOFF01 SYSTemchannelPOSClear? Scpi command Operation Status Register CommandsScpi command STATuschannelOPERationEVENt? Scpi command STATuschannelOPERationCONDition? Regulating Sub-Register Commands STATuschannelOPERationREGulatingCONDition? Shutdown Sub-Register Commands STATuschannelOPERationSHUTdownPTRansition? STATuschannelOPERationSHUTdownPROTectionENABle? Protection Shutdown Sub-Register Commands Remote Control Sub-Register Commands STATuschannelOPERationRCONtrolCONDition? Current Share Sub-Register Commands STATuschannelOPERationCSHareCONDition? STATuschannelQUEStionableENABle? Questionable Status Register Commands Voltage Sub-Register Commands STATuschannelQUEStionableVOLTageCONDition? Current Sub-Register Commands STATuschannelQUEStionableCURRentCONDition? STATuschannelQUEStionablePOWerENABle? Power Sub-Register Commands Temperature Event Sub-Register is read and then cleared Temperature Sub-Register Commands 172 Current Sharing 6000 Watt only Configure Current Share No sharingCurrent Sharing 6000 Watt only Press 7 times Setup Current Sharing Network Operation 177 178 Entering Calibration Mode Appendix A. Calibration Front Panel To access calibration mode via the front panel You are back in the Calibration menu. Output V Cal Output Cal Change CodeCode #### Setup and Equipment Front Panel Calibration Procedure Power supply will set the output voltage to 90%Output Current Output Voltage Power supply will set the output to 90% Analog Programming Interface Range Analog Programming Interface Voltage Readback Calibration Analog Programming Interface Current Programming Calibration Enter the voltage read from the external DVM. Press Enter Analog Programming Interface Current Readback Calibration Remote Interface Calibration Procedure Set the output voltage to 10% by sending the commandSet the output voltage to 90% by sending the command Set the output current to 10% by sending the command Set the output current to 90% by sending the command CALANAL5VPROGVOLTLEV MAX CALANAL5VREADVOLTLEV MIN CALANAL5VPROGCURRLEV MAX CALANAL10V Exit calibration mode Restore Factory CalibrationRestore? Y Output V Cal Appendix B. Scpi Command Reference Codes and Standards Scpi Command Hierarchy Scpi Command ReferenceIEEE-488.2/SCPI Syntax and Style Parameters Units of Measure and Multipliers CALibrationCURRentLEVel currentMINMAX Using Scpi CommandsIs the same as typing OPC *PSC Off *TRG Using Minimum Maximum QueriesCALCURRentLEVel currentMINMAX Calstat on Parameter TypesVoltprot voltageMAXMIN Tables Scpi Command SummaryNotations Table B.1IEEE 488.2 Commands Scpi Command Table B.2Readback Commands 200 Table B.3Commands for Output Control Table B.4Commands for Current Share 6000 W only 202 Table B.5Commands for Calibration Table B.6Command to Clear all Protection Mechanisms Table B.9System Commands Table B.7Commands for Fold ProtectionTable B.8Commands for Triggering Table B.10Status Commands 206 207 208 Table B.13Output State Table B.11Protection CommandsTable B.12User Lines Table B.14Auto Sequence Commands PROGramchannelSELectedSTEPNEXT 211 Table B.15Legacy Commands Legacy Command Expressions Expression Details Expressions Appendix C. Error Messages Command Error List Execution Error ListError Messages Errorcode Error Message Description Execution Error List Device-Specific Error List Error Error Message Description Code Operation Complete Event Query Error ListUser Request Event Front Panel Error Codes CPU Error CodesAnalog Programming Interface Error codes Auto Sequencing Error Codes CANbus Error Codes Multichannel Error Codes Current Share Error Codes Service Request and Polling Message TerminatorsAddress Range Address Protocol Specifications Control FunctionsInterface Ieee 488.1 Section Function Mnemonic Description Functions Subset Electrical Specifications Mechanical SpecificationsPerformance Specifications Driver Ieee 488.2 Section Performance Specifications Appendix E. Specifications and Characteristics Electrical Specifications-Summary Specifications and Characteristics 229 Models 80-75 100-60 150-40 300-20 600-10 231 Models 10-1200 20-600 30-400 40-300 60-200 233 Models 80-150 100-120 150-80 300-40 600-20 235 AC Line Input Specifications AC Line Input Voltage Operating RangesArms 6000 Watt Arms 12000 Watt Output Performance Specifications 103% of maximum rated voltage Typical Programming Resolution Typical Measurement ResolutionProgramming Accuracy1 Readback Accuracy Hour Drift Temperature Stability2 Temperature CoefficientsMinute Drift1 Analog Programming Interface Typical 31 kHz 62 kHz output ripple To 95% step in output voltageFor a programmed 95% to 5% step in output voltage Maximum Within regulation envelope Maximum deviation as a percentage of rated output voltage Minimum 3.8 V for each line, 5 V typical Environmental Specification Humidity SpecificationSpecification International Approvals Mechanical Specification Figure E.1 Power Supply Dimensions 6000 Watt unit Figure E.2 Power Supply Dimensions 12000 Watt unit Index Gpib 247 248 249 250 Page Xantrex Technology Inc