Black & Decker FS1300CSL instruction manual Tighten the lever to lock the saw shoe in place

Page 8

642742-00 01 FS1300 FS1500CSL 11/29/07 2:18 PM Page 8

Move the saw shoe (6) into the desired position. The corresponding depth of cut can be read from the scale (13).

Tighten the lever to lock the saw shoe in place.

Set depth adjustment of saw such that one tooth of the blade projects below the workpiece as shown in figure 8.

7

13

 

12

8

 

Tip of tooth

Surface of wood

ADJUSTING THE BEVEL ANGLE (FIG. 9)

This tool can be set to bevel angles between 0° and 45°.

Loosen the locking knob (14) to unlock the saw shoe.

Move the saw shoe (6) into the desired position. The corresponding bevel angle can be read from the scale (15).

Tighten the locking knob to lock the saw shoe in place.

9

14

15

ATTACHING AND REMOVING THE BLADE

REMOVING THE BLADE (FS1500CSL) (FIG. 10 & 11)

Keep the spindle lock button (5) depressed and rotate the blade until the spindle lock engages.

Loosen and remove the blade retaining screw (16) by turning it counter- clockwise using the wrench (10) supplied.

Remove the outer washer (17).

Remove the saw blade (7).

10

5

11

 

 

17

 

18

 

 

 

16

7

 

 

 

10

 

ATTACHING THE BLADE (FS1500CSL)

Place the saw blade (7) onto the inner flange (18), making sure that the arrow on the blade points in the same direction as the arrow on the tool.

Fit the outer washer (17) on the spindle, with the raised part pointing away from the saw blade.

Insert the blade retaining screw (16) into the hole.

Keep the spindle lock button (5) depressed.

Securely tighten the blade retaining screw by turning it clockwise using the wrench (10) supplied.

8

Image 8
Contents 4 inch 185mm Circular Saws VEA EL Español EN LA ContraportadaGeneral Safety Rules Specific Safety Rules Lead from lead-based paints SE These Instructions Additional Safety Rules Circular SawsCauses and Operator Prevention of Kickback 642742-00 01 FS1300 FS1500CSL 11/29/07 218 PM To Reduce the Risk of Kickback Safety Instructions LasersGuard Against Kickback Assembly / Adjustment SET-UP OverviewFollowing laser warnings are located on your saw MotorAdjusting the Bevel Angle FIG Tighten the lever to lock the saw shoe in placeTighten the locking knob to lock the saw shoe in place Attaching the Blade FS1500CSLSecure and maintain work area See Safety Rules Removing the Blade FS1300CSLAttaching the Blade FS1300CSL AttachingOperation Maintenance AccessoriesService Information Full TWO-YEAR Home USE WarrantyTechnical Specifications of Laser Guide D’UTILISATION Règles Générales DE Sécurité Lorsque votre corps est mis à la terreRègles DE Sécurité Spécifiques Utilisation ET Entretien DE L’OUTIL’OPÉRATEUR Performances et la sécurité de fonctionnement.VEffets DE Rebond Le plomb contenu dans les peintures à base de plombPROTÉGEZ-VOUS DES Effets DE Rebond Directives DE Sécurité Lasers Pour Réduire LE Risque D’EFFET DE RebondAperçu FIG MoteurRéglage DE L’ANGLE DE Biseau FIG Configuration DE ’ASSEMBLAGE ET DES RéglagesRéglage DE LA Profondeur DE Coupe ET Dépose DE LA Lame FS1300CSL ET Fonctionnement Trait LaserInterrupteur Réglage DE LA Plaque DE Trait DE Scie FIGInterrupteur DU Laser FIG Pour Utiliser LE Trait LaserSciage Conseils Pour UNE Utilisation OptimaleLubrification AccessoiresEntretien Caractéristiques Techniques DU Laser 555326-7100 Normas Generales DE Seguridad InstruccionesIncendio o lesiones personales graves.save Seguridad PersonalMantenimiento Normas DE Seguridad EspecíficasUSO Y Cuidado DE LA Herramienta Causas DEL Retroceso Y SU Prevención POR Parte DEL Operador El plomo de las pinturas de base plomo Conserve Estas InstruccionesRetroceso Manténgase Alerta Y EN Para Reducir EL Riesgo DE RetrocesoInstruccciones DE Seresseguridad Láseres Descripción General FIG ENSAMBLADO/AJUSTE Ajuste DE LA Profundidad DE Corte YAjuste DEL Ángulo DE Biselado FIG Colocación DE LA Hoja FS1500CSLExtracción DE LA Hoja FS1300CSL Y Colocación DE LA Hoja FS1300CSLColocación ExtracciónFuncionamiento Línea LáserAserrado Consejos Para UN USO ÓptimoCorte Interno Almacenamiento DE LA LlaveNota especial de Garantía para Contratistas Especificaciones Técnicas DEL Láser CULIACAN, SIN MONTERREY, N.L GUADALAJARA, JALPUEBLA, PUE MEXICO, D.F642742-00 01 FS1300 FS1500CSL 11/29/07 219 PM 642742-00 01 FS1300 FS1500CSL 11/29/07 219 PM 642742-00 01 FS1300 FS1500CSL 11/29/07 219 PM