Craftsman 286.17589 operating instructions Lubricating Instructions See Figure C

Page 16

LUBRICATING INSTRUCTIONS (See Figure C)

The blades of your Twin Cutter saw are

equipped with "dry cut teeth that under normal cuttingconditionsdo not need to be lubricated.However, in extreme cutting

conditions,such as when you are sawing into aluminum, copper, stainless steel and cast Iron, the wax lubricating device must be used.

1. Insert wax

lubricating stick into wax

 

lubricating

device.

S_ck

2.Turn feeder wheel to apply lubricant to "

blade. A 1/4 turn should provide adequate lubrication.

CUTTING INSTRUCTIONS cont.

Cutting Shaped Plates

up to 1116-in.thick (See Fig. 10)

1. When cuttingshaped metal plate

Fig. 10

ALWAYS supportthe plate evenly on both sides and in the middlewith

support blocks. This will keep it from flexing when cutting.This shouldbe done, whether you'reusing a clamping

table, or using adjustable clamps on a flat work table.

PLUNGE CUT'rING(See Figure 11)

1.Raise the retractable guard into the open positionwith your left hand,

2.Use the thumbof your left hand to hold the guard in the open positionwhile gripping the saw'sassist handle.

3.Turn on the saw and plunge the blades into the material to be cut.

4.Push the saw forward to complete the cut.

5.Turn off saw, allow blades to stop completely, then remove saw from workpiece.

6.Clean out the corners of the cut with a hand saw or sabre on project.

1

saw, depending

NOTE: When cutting building materials, blades must be kept clean with a tar and pitch blade cleaning solvent

16

Image 16
Contents Safety Operation Maintenance ESPANOL, PAGE25 In.TWIN Cutter SAWFrom the date of purchase, Return Ittothe Nearest Sears Year Full Warranty On Craftsman ToolStore or Sears Parts and Repair Center Inthe United Work Area Safety Electrical SafetyPersonalsafety Tool USE and Care SafetyServicesafety Safety Rules for SawsKICKBACK..,WHAT Causes IT and Ways to Prevent IT Causes of KickbackAdditional Rules for Safe Operation Label on your tool may Include the following symbols WattsWax UnpackingSawblades Blade Guard SystemKickback Startingcut Page Blade through the material at an angle CuttinginstructionsFeed Speed What IT Cuts Cutting ALL MaterialsLubricating Instructions See Figure C Rbor Adapter Page General Double Insulation LubricationExtension Cords Problem Cause Solution Page Qty See Back page for Parts Ordering InstructionsPage ATENClON Lea, comprenda y siga todas Seguridad = Funcionamiento MantenimientoICONSERVE Estas INSTRUCCIONES! iLEATODAS LAS Instrucciones Seguridad EN EL Lugar Detrabajo Seguridad ElectricaSeguridad Personal USO Y Cuidado DE LAS Herramientas DE SeguridadReglas DE Seguridad Para LAS Sierras RETROCESO...SUS Causasy Como SE Puede Evitar Reglasadicionalesparafuncionamientoseguro Leatodas LAS Instrucciones 500RPM Madera1metalconungrosordeparedo Idminade1/16 DesempaqueHojasdelasierra Sistema DE Proteccion DE LAS HojasRetroceso Comienzodeuncorte Importante Paraayudar Mantenerelcontrol Velocidad DE Avance InstruccionesparaloscortesCorre!o Lal l l Cortes EN Todos LOS MaterialesInstrucciones DE Lubricacion Dispositivode lubricaci6n ala ceraDESMONTAJELASHOJASDELASIERRAVerFlgs.12 Brida Generalidades Importante Aislamiento DobleCordones DE Extension Dientes despuntados CrJ Sierra DE Hoja Doble Modelo Numero MY-HOME Sears Parts and Repair Center Anytime,dayornightU.S.A