Norton Abrasives C3126, C3120, C6120 Control and Gauge locations and function Chart Type Function

Page 16

Insure that the operator is familiar with the control and gauge locations and functions before proceeding:

Control and Gauge locations and function Chart

Item	Type	Function
Engine Control Module	Control	Starts Engine, LED warning indicators and will
w/Hour Meter		shut the engine down in the event of low oil,
		over temperature, engine over speed.
Depth Lock	Control	Allows operator to cut at a preset depth
Depth Gauge	Control	Indicates cutting depth
Vernier Throttle	Control	Precise Engine speed control. Pull out or twist.
Raise/Lower Switch	Control	Raise or lower blade into work surface. To
		Raise move the switch to the rear of the saw.
		To lower move the switch forward.
Emergency Kill Switch	Control	Kills Engine when activated
Forward/Reverse Lever	Control	Controls direction and speed of machine
Transmission	Control	Engages or Disengage Transmission. NOTE:
Engage/Disengage		Only Engage the Transmission when the
Lever		Forward/Reverse Lever is in the Neutral
		Position. Engaging the Transmission when the
		Forward/Reverse Lever is not in the Neutral
		Position can damage the Transmission
		Jackshaft Gear
Ignition Power Key	Control	Energize Engine/Engine Gauge system and
Switch		Accessory Control System. Turns the machine
		off.
Fuel Cap w/Gauge	Gauge	Shows current fuel level
12-volt Power Point	Control	Auxiliary power source for 12-volt accessories
		such as: Light Kit. Can be used to charge a cell
		phone
Fuse	Control	Left side fuse protects the Accessory systems.
		Right side fuse protects the Engine Control
		System. All fuse are
		AGC Type Fuse 1/4" DIA x 1-1/4" Long, 15A
Optional Water Pump	Control	Controls optional Water Pump. NOTE: All
Switch		machines will have the switch installed at the
		factory. The water pump is a dealer installed
		option.
Blade Saver Switch	Control	Activates the Blade Saver Switch (Water
		Pressure Switch) System. When activated the
		Blade Saver Switch will shut the engine off if
		low water pressure is used.

16

Image 16

Contents Owners Manual C3120 C6120 C3126 C6126 C3130 C6130 C6136Warranty Table of Contents Safety Precautions Hazard SymbolsDust and Silica Warning Eye Protection Hearing Respiratory Head ProtectionYou Are Responsible For Your Safety Assembly C31xx Concrete Saw Specifications Dimensions/WeightCharacteristics EngineC61xx Concrete Saw Specifications Blade Size Maximum Depth Blade Shaft RPMInstalling the Blade II. OperationBlade Shaft Installation Changing the Blade Side Multiple Mounted Blades DescriptionFront Pointer Assembly Controls and Functions Never use a gasoline or an oil and gasoline mixtureControls/Gauges Location of Controls and GaugesControl and Gauge locations and function Chart Type Function Type Function Starting the EngineStraight Drive 31 & 61 HP RPMOperating the Saw Water SupplyJackshaft Drive 61HP Eye Protection Hearing Respiratory Head Protection Straight Drive 31 & 61 HP Jackshaft Drive 61HPPage Cutting Technique Depth GaugeDepth Lock Depth Gauge and Depth Lock LocationsStep Cutting Additional Guide Lines for Sawing Lead Off Adjustment Page III. Maintenance EngineLocations of Engine Components Deutz Engine Components ‡Oil Checking the Oil ‡ Oil Filler Neck and Dipstick Locations ‡Oil Specifications Oil Quality GradeApproved Oils Deutz Oil ViscosityFuel Specifications Lube Oil Change Intervals in Operating HoursDiesel Bio Diesel FuelWinter Fuel Grades Engine Service Fault Measures Cause SectionCh/Cl Ch/TAir Filter Assembly Dry Cutting Engine Maintenance Air Filter C31xxAir Filter C61xx Part DescriptionSpeed RPM Temperature Condition BearingsBearing Location Shaft Size Maximum Grease in Ounces Frequency of LubricationBelts Engine is running Hydraulic Raise/Lower SystemRemember too much tension shortens belt and bearing life Raise and Lower Speeds of the Hydraulic SystemPage Hydraulic Pump Maintenance Page Page Page Page Page Page Page Page Page Transmission Recommended Fluids For Eaton Model 6 Transmissions Self-Propelling Operations20W Straight Viscosity SE, CC, or CD Rated Engine Oil Speed Control Lever Transmission Engage/Disengage LeverTransmission Maintenance Too Move the MachineElectrical System Wiring Section a Accessory/Switches Wiring Section B Controls/Instruments Wiring Section C Wiring Harness Connector Control/Instrument SideWiring Section D Engine Wiring HarnessOrdering Information Description Part Number14, 20 and 26 Blade Size Only 36 Blade Size OnlyBlade Guard Conversion Chart Straight Drive Non-Jackshaft Models OnlyService Parts Main Frame Group 31HP and 61HP Description Shaft Cover 61 HP Engine Group 61HP AIR Filter Inner Safety Engine Group 31HP Fuel Filter Element 31HP Only Stub Shaft Group 31HP and 61HP Sold Individually Instrument Panel Group 31HP and 61HP Instrument Panel Housing Transmission and Rear Axle Group 31HP and 61HP # 40 Drive Chain Transmission and Rear Axle Group Depth Stop and Front Axle Group 31HP and 61HP Depth Stop Handle Controls and Lever Group Switch Boot Electro-Hydraulic Group 31HP and 61HP Electro-Hydraulic Group Blade Shaft Group Non-Jackshaft 31HP and 61HP Blade Shaft Group Non-Jackshaft Bearing TAP BaseBlade Guard Group Blade Guard Group 31HP and 61HP Water Control System Group Optional Water Pump Group FIT Barb ½ MPT X ½ Male Saint-Gobain Abrasives, Inc