Norton Abrasives C6126, C3120, C6120, C3126, C3130, C6136, C6130 owner manual Winter Fuel Grades

Page 34

Winter Fuel Grades:

Waxing may occur at lower temperatures which will clog the fuel system and reduce the engines efficiency. If the ambient temperature is less than 32°F (0°C) a winter grade fuel (suitable to 5°F (-15°C) should be used. If the temperature is below 5°F to -4°F (-15°C to -20°C) kerosene should be added to the fuel as shown in the following chart. If summer grade Diesel must be used at temperatures below 32°F (0°C) up to 60% kerosene can be used. Always fill tank of saw with appropriate amount of Kerosene first then add the Diesel. For more information see the Deutz Operation Manual or contact your local Deutz Service Center.

Legend

ISummer-grade Diesel Fuel

II Winter-grade Diesel Fuel

A Ambient Temperature

B Percentage of Kerosene Added

Never mix Diesel with gasoline (petrol)

34

Image 34

Contents Owners Manual C3120 C6120 C3126 C6126 C3130 C6130 C6136Warranty Table of Contents Safety Precautions Hazard SymbolsDust and Silica Warning Eye Protection Hearing Respiratory Head ProtectionYou Are Responsible For Your Safety Assembly Characteristics C31xx Concrete Saw SpecificationsDimensions/Weight EngineC61xx Concrete Saw Specifications Blade Size Maximum Depth Blade Shaft RPMInstalling the Blade II. OperationBlade Shaft Installation Changing the Blade Side Multiple Mounted Blades DescriptionFront Pointer Assembly Controls/Gauges Controls and FunctionsNever use a gasoline or an oil and gasoline mixture Location of Controls and GaugesControl and Gauge locations and function Chart Type Function Type Function Starting the EngineStraight Drive 31 & 61 HP RPMOperating the Saw Water SupplyJackshaft Drive 61HP Eye Protection Hearing Respiratory Head Protection Straight Drive 31 & 61 HP Jackshaft Drive 61HPPage Cutting Technique Depth GaugeDepth Lock Depth Gauge and Depth Lock LocationsStep Cutting Additional Guide Lines for Sawing Lead Off Adjustment Page III. Maintenance EngineLocations of Engine Components Deutz Engine Components ‡Oil Checking the Oil ‡ Oil Filler Neck and Dipstick Locations ‡Approved Oils Deutz Oil SpecificationsOil Quality Grade Oil ViscosityDiesel Fuel SpecificationsLube Oil Change Intervals in Operating Hours Bio Diesel FuelWinter Fuel Grades Ch/Cl Engine Service Fault MeasuresCause Section Ch/TAir Filter Assembly Dry Cutting Engine Maintenance Air Filter C31xxAir Filter C61xx Part DescriptionBearing Location Shaft Size Maximum Grease in Ounces Speed RPM Temperature ConditionBearings Frequency of LubricationRemember too much tension shortens belt and bearing life Belts Engine is runningHydraulic Raise/Lower System Raise and Lower Speeds of the Hydraulic SystemPage Hydraulic Pump Maintenance Page Page Page Page Page Page Page Page Page Transmission Recommended Fluids For Eaton Model 6 Transmissions Self-Propelling Operations20W Straight Viscosity SE, CC, or CD Rated Engine Oil Speed Control Lever Transmission Engage/Disengage LeverTransmission Maintenance Too Move the MachineElectrical System Wiring Section a Accessory/Switches Wiring Section B Controls/Instruments Wiring Section C Wiring Harness Connector Control/Instrument SideWiring Section D Engine Wiring Harness14, 20 and 26 Blade Size Only Ordering InformationDescription Part Number 36 Blade Size OnlyBlade Guard Conversion Chart Straight Drive Non-Jackshaft Models OnlyService Parts Main Frame Group 31HP and 61HP Description Shaft Cover 61 HP Engine Group 61HP AIR Filter Inner Safety Engine Group 31HP Fuel Filter Element 31HP Only Stub Shaft Group 31HP and 61HP Sold Individually Instrument Panel Group 31HP and 61HP Instrument Panel Housing Transmission and Rear Axle Group 31HP and 61HP # 40 Drive Chain Transmission and Rear Axle Group Depth Stop and Front Axle Group 31HP and 61HP Depth Stop Handle Controls and Lever Group Switch Boot Electro-Hydraulic Group 31HP and 61HP Electro-Hydraulic Group Blade Shaft Group Non-Jackshaft 31HP and 61HP Blade Shaft Group Non-Jackshaft Bearing TAP BaseBlade Guard Group Blade Guard Group 31HP and 61HP Water Control System Group Optional Water Pump Group FIT Barb ½ MPT X ½ Male Saint-Gobain Abrasives, Inc