Norton Abrasives C6120, C3120, C3126, C3130, C6136, C6130, C6126 owner manual Air Filter Assembly

Page 36

B. Air Filter Assembly:

Please note that the Air Filter Assembly for the 31HP and 61HP Engines are different and do not interchange. The C31xx units are equipped with a 31HP Deutz Diesel engine see section Air Filter C31xx on page 37 for details. The C61xx units are equipped with a 61HP Deutz Turbo Charged Diesel engine see section Air Filter C61xx on page 38 for details.

Air Filter Assembly Maintenance:

1.Inspect and clean Inner and Outer Filters

a.Inspect the Inner and Outer Filters for damage to the Filter and Gasket. If damage DO NOT USE replace immediately. Using an engine with a damaged filter can destroy the engine and is not covered under warranty.

b.Clean the Inner and Outer Filters at least once a month if cutting dry. If cutting dry inspect on a weekly. Clean the Filters by using dry compressed air maximum of 73 psi (5 bar) of pressure, blow from the inside out. DO NOT wash the filters as this will damage the units. Replace the filters when the damaged. Do not clean the air filter with gasoline or other flammable solvents. A fire or explosion could result.

2.Inspect Gaskets located on the Filters for damage. The Gaskets can be damaged through regular removal and replacement. Replace if damaged. Do not use if damaged.

3.Insure that the Filters are properly installed in the Filter Housing before use. Never use the machine with out both Filters installed. If the engine can be damaged if dust or dirt is ingested and is not covered under any warranties.

4.Empty Dust Boot (Dust Discharge Valve) on a daily bases. The Dust Boot is located on the bottom of the Air Filter Assembly. To empty press the sides of the Dust Boot together as shown below:

Dust Boot

5. Inspect and Clean Pre-Filter weekly.

36

Image 36
Contents Owners Manual C3120 C6120 C3126 C6126 C3130 C6130 C6136Warranty Table of Contents Safety Precautions Hazard SymbolsDust and Silica Warning Eye Protection Hearing Respiratory Head ProtectionYou Are Responsible For Your Safety Assembly C31xx Concrete Saw Specifications Dimensions/WeightCharacteristics EngineC61xx Concrete Saw Specifications Blade Size Maximum Depth Blade Shaft RPMInstalling the Blade II. OperationBlade Shaft Installation Changing the Blade Side Multiple Mounted Blades DescriptionFront Pointer Assembly Controls and Functions Never use a gasoline or an oil and gasoline mixtureControls/Gauges Location of Controls and GaugesControl and Gauge locations and function Chart Type Function Type Function Starting the EngineStraight Drive 31 & 61 HP RPMWater Supply Operating the SawJackshaft Drive 61HP Eye Protection Hearing Respiratory Head Protection Straight Drive 31 & 61 HP Jackshaft Drive 61HPPage Cutting Technique Depth GaugeDepth Lock Depth Gauge and Depth Lock LocationsStep Cutting Additional Guide Lines for Sawing Lead Off Adjustment Page III. Maintenance EngineLocations of Engine Components Deutz Engine Components ‡Oil Checking the Oil ‡ Oil Filler Neck and Dipstick Locations ‡Oil Specifications Oil Quality GradeApproved Oils Deutz Oil ViscosityFuel Specifications Lube Oil Change Intervals in Operating HoursDiesel Bio Diesel FuelWinter Fuel Grades Engine Service Fault Measures Cause SectionCh/Cl Ch/TAir Filter Assembly Dry Cutting Engine Maintenance Air Filter C31xxAir Filter C61xx Part DescriptionSpeed RPM Temperature Condition BearingsBearing Location Shaft Size Maximum Grease in Ounces Frequency of LubricationBelts Engine is running Hydraulic Raise/Lower SystemRemember too much tension shortens belt and bearing life Raise and Lower Speeds of the Hydraulic SystemPage Hydraulic Pump Maintenance Page Page Page Page Page Page Page Page Page Transmission Self-Propelling Operations Recommended Fluids For Eaton Model 6 Transmissions20W Straight Viscosity SE, CC, or CD Rated Engine Oil Speed Control Lever Transmission Engage/Disengage LeverTransmission Maintenance Too Move the MachineElectrical System Wiring Section a Accessory/Switches Wiring Section B Controls/Instruments Wiring Section C Wiring Harness Connector Control/Instrument SideWiring Section D Engine Wiring HarnessOrdering Information Description Part Number14, 20 and 26 Blade Size Only 36 Blade Size OnlyBlade Guard Conversion Chart Straight Drive Non-Jackshaft Models OnlyService Parts Main Frame Group 31HP and 61HP Description Shaft Cover 61 HP Engine Group 61HP AIR Filter Inner Safety Engine Group 31HP Fuel Filter Element 31HP Only Stub Shaft Group 31HP and 61HP Sold Individually Instrument Panel Group 31HP and 61HP Instrument Panel Housing Transmission and Rear Axle Group 31HP and 61HP # 40 Drive Chain Transmission and Rear Axle Group Depth Stop and Front Axle Group 31HP and 61HP Depth Stop Handle Controls and Lever Group Switch Boot Electro-Hydraulic Group 31HP and 61HP Electro-Hydraulic Group Blade Shaft Group Non-Jackshaft 31HP and 61HP Blade Shaft Group Non-Jackshaft Bearing TAP BaseBlade Guard Group Blade Guard Group 31HP and 61HP Water Control System Group Optional Water Pump Group FIT Barb ½ MPT X ½ Male Saint-Gobain Abrasives, Inc