Norton Abrasives C3130, C3120, C6120, C3126, C6136, C6130, C6126 owner manual Switch Boot

Page 80

Controls and Lever Group

ITEM	DESCRIPTION	PART No.	ITEM	DESCRIPTION	PART No.
1	SWITCH BOOT	N1C0072	22	ROD END	N1C0075

2	SCREW	N1D0240	23	THREADED ROD	N1E0080

3	SWITCH MNT. PL	N1E0243	24	NUT 3/8-24 HEX JAM GR2 ZN	231054

4	RAISE/LOWER SWITCH	N1C0088	25	BELL CRANK	N1E0071

5	RUBBER BOOT	N1C0375	26	WASHER 3/8 SPRING LOCK	8177012

6	SWITCH HANDLE	N1E0265	27	NUT 3/8-16 HEX	8142003

7	NUT 7/8-9 HEX JAM	8150009	28	SCR 3/8-16 X 2 HEX HD CAP	8041054

8	SPEED CONTROL LEVER	237389	29	THREADED ROD	N1E0081

9	FRICTION PAD	N1E0059

10	SCR 3/8-16 X 2 HEX HD CAP	8041054

11	WASHER 3/8 SAE ZN PLT	8172009

12	NUT 3/8-16 HEX LOCK	8162003

13	LEVER SUPPORT	N1E0058

14	SCR 1/4-20 X 3/4 HEX HD CAP	8041004

15	NUT 1/4-20 HEX LOCK	8160001

16	ENGAGE. LEVER	237382

17	HAND GRIP	N1C0005

18	GATE PLATE	N1E0079

19	SCR 3/8-16 X 1 1/2 HEX HD CAP	8041052

20	TRANS CONTROL LEVER	237321

21	NUT 1/2-13 HEX	8143005

80

Image 80

Contents Owners Manual C3120 C6120 C3126 C6126 C3130 C6130 C6136Warranty Table of Contents Safety Precautions Hazard SymbolsDust and Silica Warning Eye Protection Hearing Respiratory Head ProtectionYou Are Responsible For Your Safety Assembly C31xx Concrete Saw Specifications Dimensions/WeightCharacteristics EngineC61xx Concrete Saw Specifications Blade Size Maximum Depth Blade Shaft RPMInstalling the Blade II. OperationBlade Shaft Installation Changing the Blade Side Multiple Mounted Blades DescriptionFront Pointer Assembly Controls and Functions Never use a gasoline or an oil and gasoline mixtureControls/Gauges Location of Controls and GaugesControl and Gauge locations and function Chart Type Function Type Function Starting the EngineStraight Drive 31 & 61 HP RPMJackshaft Drive 61HP Water SupplyOperating the Saw Eye Protection Hearing Respiratory Head Protection Straight Drive 31 & 61 HP Jackshaft Drive 61HPPage Cutting Technique Depth GaugeDepth Lock Depth Gauge and Depth Lock LocationsStep Cutting Additional Guide Lines for Sawing Lead Off Adjustment Page III. Maintenance EngineLocations of Engine Components Deutz Engine Components ‡Oil Checking the Oil ‡ Oil Filler Neck and Dipstick Locations ‡Oil Specifications Oil Quality GradeApproved Oils Deutz Oil ViscosityFuel Specifications Lube Oil Change Intervals in Operating HoursDiesel Bio Diesel FuelWinter Fuel Grades Engine Service Fault Measures Cause SectionCh/Cl Ch/TAir Filter Assembly Dry Cutting Engine Maintenance Air Filter C31xxAir Filter C61xx Part DescriptionSpeed RPM Temperature Condition BearingsBearing Location Shaft Size Maximum Grease in Ounces Frequency of LubricationBelts Engine is running Hydraulic Raise/Lower SystemRemember too much tension shortens belt and bearing life Raise and Lower Speeds of the Hydraulic SystemPage Hydraulic Pump Maintenance Page Page Page Page Page Page Page Page Page Transmission 20W Straight Viscosity SE, CC, or CD Rated Engine Oil Self-Propelling OperationsRecommended Fluids For Eaton Model 6 Transmissions Speed Control Lever Transmission Engage/Disengage LeverTransmission Maintenance Too Move the MachineElectrical System Wiring Section a Accessory/Switches Wiring Section B Controls/Instruments Wiring Section C Wiring Harness Connector Control/Instrument SideWiring Section D Engine Wiring HarnessOrdering Information Description Part Number14, 20 and 26 Blade Size Only 36 Blade Size OnlyBlade Guard Conversion Chart Straight Drive Non-Jackshaft Models OnlyService Parts Main Frame Group 31HP and 61HP Description Shaft Cover 61 HP Engine Group 61HP AIR Filter Inner Safety Engine Group 31HP Fuel Filter Element 31HP Only Stub Shaft Group 31HP and 61HP Sold Individually Instrument Panel Group 31HP and 61HP Instrument Panel Housing Transmission and Rear Axle Group 31HP and 61HP # 40 Drive Chain Transmission and Rear Axle Group Depth Stop and Front Axle Group 31HP and 61HP Depth Stop Handle Controls and Lever Group Switch Boot Electro-Hydraulic Group 31HP and 61HP Electro-Hydraulic Group Blade Shaft Group Non-Jackshaft 31HP and 61HP Blade Shaft Group Non-Jackshaft Bearing TAP BaseBlade Guard Group Blade Guard Group 31HP and 61HP Water Control System Group Optional Water Pump Group FIT Barb ½ MPT X ½ Male Saint-Gobain Abrasives, Inc