Norton Abrasives C6126, C3120, C6120, C3126, C3130 Too Move the Machine, Transmission Maintenance

Page 55

Too Move the Machine:

When the Transmission Engage/Disengage Lever is engaged, pushing the Forward/Reverse Lever slowly forward will increase the forward speed of the saw. Pulling it to the center will place the saw in neutral. The machine is equipped with a Neutral Lockout. To operate the Forward/Reverse Lever either: move the lever towards the Operator’s left side then move the Forward/Reverse Lever to the desired position. Pulling the saw to the rear of the console (from the neutral) will increase the reverse speed. The S

A.With the machine running, insure that the machine’s Forward/Reverse Lever is in the Neutral position.

B.Place the Engage/Disengage Lever into the Engage position.

C.Move the Forward/Reverse Lever towards the Operator’s left side and then move the Forward/Reverse Lever to the desired position. The machine is equipped with a Neutral Lockout which prevents the Forward/Reverse Lever from accidentally being moved from the Neutral Position. Pushing the Forward/Reverse Lever slowly forward will increase the forward speed of the saw moving the Forward/Reverse Lever towards the rear of the machine will increase the reward or reverse speed.

3.Transmission Maintenance:

A.Keep the chain clean and properly adjusted.

B.Keep all linkages properly adjusted.

C.Keep Transmission Belt aligned and in good condition. Replace the belt if it worn or cracked.

D.Check Rear Axle Drive Gears for:

1.Misalignment

2.Broken Teeth

3.Unusual wear patterns

4.Keep Clean

55

Image 55

Contents C3120 C6120 C3126 C6126 C3130 C6130 C6136 Owners ManualWarranty Table of Contents Hazard Symbols Safety PrecautionsEye Protection Hearing Respiratory Head Protection Dust and Silica WarningYou Are Responsible For Your Safety Assembly Engine C31xx Concrete Saw SpecificationsDimensions/Weight CharacteristicsBlade Size Maximum Depth Blade Shaft RPM C61xx Concrete Saw SpecificationsII. Operation Installing the BladeBlade Shaft Installation Changing the Blade Side Description Multiple Mounted BladesFront Pointer Assembly Location of Controls and Gauges Controls and FunctionsNever use a gasoline or an oil and gasoline mixture Controls/GaugesControl and Gauge locations and function Chart Type Function Starting the Engine Type FunctionRPM Straight Drive 31 & 61 HPOperating the Saw Water SupplyJackshaft Drive 61HP Eye Protection Hearing Respiratory Head Protection Jackshaft Drive 61HP Straight Drive 31 & 61 HPPage Depth Gauge Cutting TechniqueDepth Gauge and Depth Lock Locations Depth LockStep Cutting Additional Guide Lines for Sawing Lead Off Adjustment Page Engine III. MaintenanceDeutz Engine Components ‡ Locations of Engine ComponentsOil Filler Neck and Dipstick Locations ‡ Oil Checking the Oil ‡Oil Viscosity Oil SpecificationsOil Quality Grade Approved Oils DeutzBio Diesel Fuel Fuel SpecificationsLube Oil Change Intervals in Operating Hours DieselWinter Fuel Grades Ch/T Engine Service Fault MeasuresCause Section Ch/ClAir Filter Assembly Air Filter C31xx Dry Cutting Engine MaintenancePart Description Air Filter C61xxFrequency of Lubrication Speed RPM Temperature ConditionBearings Bearing Location Shaft Size Maximum Grease in OuncesRaise and Lower Speeds of the Hydraulic System Belts Engine is runningHydraulic Raise/Lower System Remember too much tension shortens belt and bearing lifePage Hydraulic Pump Maintenance Page Page Page Page Page Page Page Page Page Transmission Recommended Fluids For Eaton Model 6 Transmissions Self-Propelling Operations20W Straight Viscosity SE, CC, or CD Rated Engine Oil Transmission Engage/Disengage Lever Speed Control LeverToo Move the Machine Transmission MaintenanceElectrical System Wiring Section a Accessory/Switches Wiring Section B Controls/Instruments Control/Instrument Side Wiring Section C Wiring Harness ConnectorWiring Harness Wiring Section D Engine36 Blade Size Only Ordering InformationDescription Part Number 14, 20 and 26 Blade Size OnlyStraight Drive Non-Jackshaft Models Only Blade Guard Conversion ChartService Parts Main Frame Group 31HP and 61HP Description Shaft Cover 61 HP Engine Group 61HP AIR Filter Inner Safety Engine Group 31HP Fuel Filter Element 31HP Only Stub Shaft Group 31HP and 61HP Sold Individually Instrument Panel Group 31HP and 61HP Instrument Panel Housing Transmission and Rear Axle Group 31HP and 61HP # 40 Drive Chain Transmission and Rear Axle Group Depth Stop and Front Axle Group 31HP and 61HP Depth Stop Handle Controls and Lever Group Switch Boot Electro-Hydraulic Group 31HP and 61HP Electro-Hydraulic Group Blade Shaft Group Non-Jackshaft 31HP and 61HP Bearing TAP Base Blade Shaft Group Non-JackshaftBlade Guard Group Blade Guard Group 31HP and 61HP Water Control System Group Optional Water Pump Group FIT Barb ½ MPT X ½ Male Saint-Gobain Abrasives, Inc