Norton Abrasives C6120, C3120, C3126, C3130, C6136, C6130, C6126 owner manual

Page 43

7.For warranty and service information on Monarch Hydraulic pumps, contact Monarch Hydraulics at:

Phone: 616-458-1306

Web Site: http://www.monarchhyd.com/

The Norton Company does not warranty the Hydraulic Pump. If any warranty or service of the Hydraulic Pump is required contact your nearest Monarch Hydraulics service center @ (616) 458-1306, or from the Internet: http://www.monarchhyd.com/

8.Monarch Hydraulic Pump Symptom /Cause

Symptom

Cause

Motor Fails To Start

Motor Start Solenoid Switch

 

Electrical Switch "Open" Circuit Motor

Load Fails To Hold

Check Valve-Main (Poppet Type)

 

D.R. Lowering Valve (two-way, Two Position)

 

Manual Override

Load Drops Slow

D.R. Lowering Valve (two-way, Two Position)

 

System Filter

Motor Runs But Load Fails To Raise

D.R. Lowering Valve (two-way, Two Position)

 

Manual Override

 

"Ground Fault'

 

Relief Valve

 

Suction Filter

 

Pump Losing Prime (Low Or No Oil In Pump)

 

Cylinder - Piston Type

 

Worn Pump

Motor Runs Slow And Sluggish

Low Voltage

 

Motor

 

Relief Valve

Load Fails To Lower

D.R. Lowering Valve (two-way, Two Position)

 

System Filter

 

Electrical Switch

 

"Open" Circuit

9. Monarch Hydraulic Pump Test Equipment a. Pressure Group:

A small 0 5000 PSI pressure gauge, preferably glycerin filled, is a very valuable and relatively inexpensive tool for checking pressure in the various sections of the circuit.

b. DC Test Light:

A test light is simply a light bulb which has one end connected by a wire to an alligator clip and the other end connected to a metal probe. It is used to check the electrical circuit when the battery is connected to the system. The alligator clip is grounded and the light glows when

43

Image 43
Contents C3120 C6120 C3126 C6126 C3130 C6130 C6136 Owners ManualWarranty Table of Contents Hazard Symbols Safety PrecautionsEye Protection Hearing Respiratory Head Protection Dust and Silica WarningYou Are Responsible For Your Safety Assembly Engine C31xx Concrete Saw SpecificationsDimensions/Weight CharacteristicsBlade Size Maximum Depth Blade Shaft RPM C61xx Concrete Saw SpecificationsII. Operation Installing the BladeBlade Shaft Installation Changing the Blade Side Description Multiple Mounted BladesFront Pointer Assembly Location of Controls and Gauges Controls and FunctionsNever use a gasoline or an oil and gasoline mixture Controls/GaugesControl and Gauge locations and function Chart Type Function Starting the Engine Type FunctionRPM Straight Drive 31 & 61 HPOperating the Saw Water SupplyJackshaft Drive 61HP Eye Protection Hearing Respiratory Head Protection Jackshaft Drive 61HP Straight Drive 31 & 61 HPPage Depth Gauge Cutting TechniqueDepth Gauge and Depth Lock Locations Depth LockStep Cutting Additional Guide Lines for Sawing Lead Off Adjustment Page Engine III. MaintenanceDeutz Engine Components ‡ Locations of Engine ComponentsOil Filler Neck and Dipstick Locations ‡ Oil Checking the Oil ‡Oil Viscosity Oil SpecificationsOil Quality Grade Approved Oils DeutzBio Diesel Fuel Fuel SpecificationsLube Oil Change Intervals in Operating Hours DieselWinter Fuel Grades Ch/T Engine Service Fault MeasuresCause Section Ch/ClAir Filter Assembly Air Filter C31xx Dry Cutting Engine MaintenancePart Description Air Filter C61xxFrequency of Lubrication Speed RPM Temperature ConditionBearings Bearing Location Shaft Size Maximum Grease in OuncesRaise and Lower Speeds of the Hydraulic System Belts Engine is runningHydraulic Raise/Lower System Remember too much tension shortens belt and bearing lifePage Hydraulic Pump Maintenance Page Page Page Page Page Page Page Page Page Transmission Recommended Fluids For Eaton Model 6 Transmissions Self-Propelling Operations20W Straight Viscosity SE, CC, or CD Rated Engine Oil Transmission Engage/Disengage Lever Speed Control LeverToo Move the Machine Transmission MaintenanceElectrical System Wiring Section a Accessory/Switches Wiring Section B Controls/Instruments Control/Instrument Side Wiring Section C Wiring Harness ConnectorWiring Harness Wiring Section D Engine36 Blade Size Only Ordering InformationDescription Part Number 14, 20 and 26 Blade Size OnlyStraight Drive Non-Jackshaft Models Only Blade Guard Conversion ChartService Parts Main Frame Group 31HP and 61HP Description Shaft Cover 61 HP Engine Group 61HP AIR Filter Inner Safety Engine Group 31HP Fuel Filter Element 31HP Only Stub Shaft Group 31HP and 61HP Sold Individually Instrument Panel Group 31HP and 61HP Instrument Panel Housing Transmission and Rear Axle Group 31HP and 61HP # 40 Drive Chain Transmission and Rear Axle Group Depth Stop and Front Axle Group 31HP and 61HP Depth Stop Handle Controls and Lever Group Switch Boot Electro-Hydraulic Group 31HP and 61HP Electro-Hydraulic Group Blade Shaft Group Non-Jackshaft 31HP and 61HP Bearing TAP Base Blade Shaft Group Non-JackshaftBlade Guard Group Blade Guard Group 31HP and 61HP Water Control System Group Optional Water Pump Group FIT Barb ½ MPT X ½ Male Saint-Gobain Abrasives, Inc