Norton Abrasives C6126, C3120, C6120, C3126 Eye Protection Hearing Respiratory Head Protection

Page 20

Lethal Exhaust: Gas use only in well ventilated areas. Engine exhaust gases contain poisonous carbon monoxide which is odorless, colorless, and can cause death if inhaled. Avoid inhaling exhaust fumes, and never run the engine in a closed building or confined area.

Use Approved:

Eye Protection

Hearing

Respiratory

Head Protection

 

Protection

Protection

 

1.To install the blade follow the instructions located in section A. Installing the Blade (page 10 to 12) of this manual. Also read and understand this complete manual beginning.

2.Check the Engine Oil level.

3.Disengage the Self-propelling unit by moving the Transmission Engage/Disengage lever fully up and place the Forward/Reverse lever in the neutral position (middle).

4.Raise the saw to the full upright position. Do not let the blade come in contact with the ground or any object.

5.Maneuver the saw to the desired starting point.

6.If wet cutting connect the water supply to the saw.

7.Follow the instructions for starting the located in section B. Engine subsection 5. Starting the Engine of this manual (pages 15 to 16).

20

Image 20
Contents Owners Manual C3120 C6120 C3126 C6126 C3130 C6130 C6136Warranty Table of Contents Safety Precautions Hazard SymbolsDust and Silica Warning Eye Protection Hearing Respiratory Head ProtectionYou Are Responsible For Your Safety Assembly C31xx Concrete Saw Specifications Dimensions/WeightCharacteristics EngineC61xx Concrete Saw Specifications Blade Size Maximum Depth Blade Shaft RPMInstalling the Blade II. OperationBlade Shaft Installation Changing the Blade Side Multiple Mounted Blades DescriptionFront Pointer Assembly Controls and Functions Never use a gasoline or an oil and gasoline mixtureControls/Gauges Location of Controls and GaugesControl and Gauge locations and function Chart Type Function Type Function Starting the EngineStraight Drive 31 & 61 HP RPMJackshaft Drive 61HP Water SupplyOperating the Saw Eye Protection Hearing Respiratory Head Protection Straight Drive 31 & 61 HP Jackshaft Drive 61HPPage Cutting Technique Depth GaugeDepth Lock Depth Gauge and Depth Lock LocationsStep Cutting Additional Guide Lines for Sawing Lead Off Adjustment Page III. Maintenance EngineLocations of Engine Components Deutz Engine Components ‡Oil Checking the Oil ‡ Oil Filler Neck and Dipstick Locations ‡Oil Specifications Oil Quality GradeApproved Oils Deutz Oil ViscosityFuel Specifications Lube Oil Change Intervals in Operating HoursDiesel Bio Diesel FuelWinter Fuel Grades Engine Service Fault Measures Cause SectionCh/Cl Ch/TAir Filter Assembly Dry Cutting Engine Maintenance Air Filter C31xxAir Filter C61xx Part DescriptionSpeed RPM Temperature Condition BearingsBearing Location Shaft Size Maximum Grease in Ounces Frequency of LubricationBelts Engine is running Hydraulic Raise/Lower SystemRemember too much tension shortens belt and bearing life Raise and Lower Speeds of the Hydraulic SystemPage Hydraulic Pump Maintenance Page Page Page Page Page Page Page Page Page Transmission 20W Straight Viscosity SE, CC, or CD Rated Engine Oil Self-Propelling OperationsRecommended Fluids For Eaton Model 6 Transmissions Speed Control Lever Transmission Engage/Disengage LeverTransmission Maintenance Too Move the MachineElectrical System Wiring Section a Accessory/Switches Wiring Section B Controls/Instruments Wiring Section C Wiring Harness Connector Control/Instrument SideWiring Section D Engine Wiring HarnessOrdering Information Description Part Number14, 20 and 26 Blade Size Only 36 Blade Size OnlyBlade Guard Conversion Chart Straight Drive Non-Jackshaft Models OnlyService Parts Main Frame Group 31HP and 61HP Description Shaft Cover 61 HP Engine Group 61HP AIR Filter Inner Safety Engine Group 31HP Fuel Filter Element 31HP Only Stub Shaft Group 31HP and 61HP Sold Individually Instrument Panel Group 31HP and 61HP Instrument Panel Housing Transmission and Rear Axle Group 31HP and 61HP # 40 Drive Chain Transmission and Rear Axle Group Depth Stop and Front Axle Group 31HP and 61HP Depth Stop Handle Controls and Lever Group Switch Boot Electro-Hydraulic Group 31HP and 61HP Electro-Hydraulic Group Blade Shaft Group Non-Jackshaft 31HP and 61HP Blade Shaft Group Non-Jackshaft Bearing TAP BaseBlade Guard Group Blade Guard Group 31HP and 61HP Water Control System Group Optional Water Pump Group FIT Barb ½ MPT X ½ Male Saint-Gobain Abrasives, Inc