Norton Abrasives C6130, C3120, C6120, C3126 Water Supply, Operating the Saw, Jackshaft Drive 61HP

Page 19

Jackshaft Drive 61HP:

 

 

 

 

 

Blade

Blade

Engine

Engine Pulley

Blade

Blade Shaft

Collar

Diameter

RPM

Diameter

Shaft RPM

Pulley Diameter

Diameter

42 inch

 

4.0 inch

 

6 inch

8 inch

(1067mm)

2800

(102 mm)

890

(152mm)

(203mm)

48 inch

 

4.0 inch

 

6 inch

8 inch

(1219mm)

2500

(102 mm)

800

(152mm)

(203mm)

D. Water Supply

Pressurized source: Turn the water control to full "ON" when using wet cutting blades. The required flow rate is 5 to 8 gallons per minute.

Optional Water Pump: The optional water pump is centrifugal pump designed to boost the flow rate of the water. In order for the optional water pump to work correctly the system requires a pressurized water source or the water source must be above the pump. The optional water pump will not draw water from a supply tank. The part number for the optional water pump kit is 237243.

1.Centrifugal pumps have a single rotating impeller. Liquid enters at the center and is thrown outward radically by the centrifugal force. The impeller is not in contact with other parts resulting in quiet efficient pumping action. This pump is not self priming. It must be located below the liquid level so liquid will flow to it by gravity. Air traps in piping must be avoided. Avoid down loops where air can be trapped.

2.Excessive system pressure above 15 P.S.I. is not recommended as he seal could be forced out of the pump housing. If water is to be pumped to the saw; always place an inline shut-off valve in front of the water pump.

3.Replacement Water Pump Seal Kit: Part Number 107523

E.Operating the Saw

Before beginning inspect the work area, machine, and blade for problems or hazards. Some areas may have underground utilities (water, gas lines, or electrical lines) located and mark all utilities before beginning. Do not run this machine or any internal combustion engine indoors or underground with out proper ventilation and a proper exhaust system for indoors or underground usage. The machine is not supplied with the proper exhaust for indoors or underground usage.

19

Image 19
Contents C3120 C6120 C3126 C6126 C3130 C6130 C6136 Owners ManualWarranty Table of Contents Hazard Symbols Safety PrecautionsEye Protection Hearing Respiratory Head Protection Dust and Silica WarningYou Are Responsible For Your Safety Assembly Engine C31xx Concrete Saw SpecificationsDimensions/Weight CharacteristicsBlade Size Maximum Depth Blade Shaft RPM C61xx Concrete Saw SpecificationsII. Operation Installing the BladeBlade Shaft Installation Changing the Blade Side Description Multiple Mounted BladesFront Pointer Assembly Location of Controls and Gauges Controls and FunctionsNever use a gasoline or an oil and gasoline mixture Controls/GaugesControl and Gauge locations and function Chart Type Function Starting the Engine Type FunctionRPM Straight Drive 31 & 61 HPOperating the Saw Water SupplyJackshaft Drive 61HP Eye Protection Hearing Respiratory Head Protection Jackshaft Drive 61HP Straight Drive 31 & 61 HPPage Depth Gauge Cutting TechniqueDepth Gauge and Depth Lock Locations Depth LockStep Cutting Additional Guide Lines for Sawing Lead Off Adjustment Page Engine III. MaintenanceDeutz Engine Components ‡ Locations of Engine ComponentsOil Filler Neck and Dipstick Locations ‡ Oil Checking the Oil ‡Oil Viscosity Oil SpecificationsOil Quality Grade Approved Oils DeutzBio Diesel Fuel Fuel SpecificationsLube Oil Change Intervals in Operating Hours DieselWinter Fuel Grades Ch/T Engine Service Fault MeasuresCause Section Ch/ClAir Filter Assembly Air Filter C31xx Dry Cutting Engine MaintenancePart Description Air Filter C61xxFrequency of Lubrication Speed RPM Temperature ConditionBearings Bearing Location Shaft Size Maximum Grease in OuncesRaise and Lower Speeds of the Hydraulic System Belts Engine is runningHydraulic Raise/Lower System Remember too much tension shortens belt and bearing lifePage Hydraulic Pump Maintenance Page Page Page Page Page Page Page Page Page Transmission Recommended Fluids For Eaton Model 6 Transmissions Self-Propelling Operations20W Straight Viscosity SE, CC, or CD Rated Engine Oil Transmission Engage/Disengage Lever Speed Control LeverToo Move the Machine Transmission MaintenanceElectrical System Wiring Section a Accessory/Switches Wiring Section B Controls/Instruments Control/Instrument Side Wiring Section C Wiring Harness ConnectorWiring Harness Wiring Section D Engine36 Blade Size Only Ordering InformationDescription Part Number 14, 20 and 26 Blade Size OnlyStraight Drive Non-Jackshaft Models Only Blade Guard Conversion ChartService Parts Main Frame Group 31HP and 61HP Description Shaft Cover 61 HP Engine Group 61HP AIR Filter Inner Safety Engine Group 31HP Fuel Filter Element 31HP Only Stub Shaft Group 31HP and 61HP Sold Individually Instrument Panel Group 31HP and 61HP Instrument Panel Housing Transmission and Rear Axle Group 31HP and 61HP # 40 Drive Chain Transmission and Rear Axle Group Depth Stop and Front Axle Group 31HP and 61HP Depth Stop Handle Controls and Lever Group Switch Boot Electro-Hydraulic Group 31HP and 61HP Electro-Hydraulic Group Blade Shaft Group Non-Jackshaft 31HP and 61HP Bearing TAP Base Blade Shaft Group Non-JackshaftBlade Guard Group Blade Guard Group 31HP and 61HP Water Control System Group Optional Water Pump Group FIT Barb ½ MPT X ½ Male Saint-Gobain Abrasives, Inc