Graco H50, H40, H25 important safety instructions Electric Shock Hazard

Page 9

Warnings

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equip- ment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable.

WARNING

ELECTRIC SHOCK HAZARD

This equipment must be grounded. Improper grounding, setup, or usage of the system can cause electric shock.

•Turn off and disconnect power at main switch before disconnecting any cables and before servicing equipment.

•Connect only to grounded power source.

•All electrical wiring must be done by a qualified electrician and comply with all local codes and regulations.

TOXIC FLUID OR FUMES HAZARD

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed.

•Read MSDSs to know the specific hazards of the fluids you are using.

•Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

•Always wear chemically impermeable gloves when spraying, dispensing, or cleaning equipment.

PERSONAL PROTECTIVE EQUIPMENT

You must wear appropriate protective equipment when operating, servicing, or when in the operating area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic fumes, burns, and hearing loss. This equipment includes but is not limited to:

•Protective eyewear

•Clothing and respirator as recommended by the fluid and solvent manufacturer

•Gloves

•Hearing protection

312062W

9

Image 9

Contents Operation Important Safety InstructionsContents Systems GCP2R2 Series ModelsApprovals XP2 SeriesSupplied Manuals Reactor Electrical DiagramsReactor Hydraulic Proportioner Part Description Part DescriptionRelated Manuals Electric Shock Hazard Skin Injection Hazard Pressurized Aluminum Parts Hazard Isocyanate Conditions Important Two-Component Material InformationMaterial Self-ignition Keep Components a and B SeparateChanging Materials Foam Resins with 245 fa Blowing AgentsKey for FIG Typical Installation, with circulationSide Supply Detail Side Supply Detail MTypical Installation, without circulation Typical Installation, without circulationComponent Identification Detail of Serial No Plate inside cabinet Detail of Reactor Fluid Manifold shroud removed for clarityTemperature Controls and Indicators Main Power SwitchRed Stop Button Target Temperature Key/LED Actual Temperature Key/LEDTemperature Scale Keys/LEDs Temperature Arrow KeysSize Component Circuit BreakersMotor ON/OFF Key/LED PSI/BAR Keys/LEDs Motor Controls and IndicatorsPark Key/LED Pressure Key/LEDCycle Count Key/LED Spray AdjustmentsHydraulic Pressure Control Knob Motor Control Arrow KeysSetup Locate ReactorGeneral equipment guidelines Electrical Requirements KW/Full Load Amps Phase Amps WattsElectrical Requirements Full Load Voltage Peak System PartCord Specification Power Cord RequirementsConnect electrical cord Part Model AWG mmConnect feed pumps Connect pressure relief lines Install Fluid Temperature Sensor FTSClose gun fluid manifold valves a and B Connect heated hoseConnect whip hose to gun fluid mani- fold Pressure check hoseLubrication system setup Ground systemCheck hydraulic fluid level Check generator fuel level StartupSet temperatures Manual current control mode only Set pressure Change pressure imbalance setting optionalPSI BAR Available Pressure Imbalance SettingsSpraying Open gun fluid manifold valves a and B Standby Shutdown Pressure Relief Procedure Lation Fluid CirculationCirculation Through Gun Manifold Code Code Name Alarm Zone Diagnostic CodesCode Code Name Alarm or Motor Control Diagnostic CodesFrequency of Oil Changes Ambient Recommended Temperature MaintenanceFluid Inlet Strainer Fluid Inlet Strainer ScreenPump Lubrication System Pump Lubrication SystemFlushing Dimensions Dimension In. mmTop View Category Data Technical DataPerformance Charts Foam Performance ChartCoatings Performance Chart Flow Rate in gpm lpm 110Graco Information Graco Standard Warranty