Graco H40 Connect electrical cord, Power Cord Requirements, Cord Specification, Part Model AWG mm

Page 25

Setup

4. Connect electrical cord

Power cord is not supplied. See Table 2.

Table 2: Power Cord Requirements

		Cord Specification
Part	Model	AWG (mm2)
253400	H-40	4 (21.2), 2 wire + ground
253401	H-40	4 (21.2), 3 wire + ground
253402	H-40	8 (8.4), 4 wire + ground
253403	H-XP3	4 (21.2), 2 wire + ground
253404	H-XP3	4 (21.2), 3 wire + ground
253405	H-XP3	6 (13.3), 4 wire + ground
253407	H-40	4 (21.2), 3 wire + ground
253408	H-40	6 (13.3), 4 wire + ground
255400	H-25	4 (21.2), 2 wire + ground
255401	H-25	8 (8.4), 3 wire + ground
255402	H-25	8 (8.4), 4 wire + ground
255403	H-XP2	4 (21.2), 2 wire + ground
255404	H-XP2	6 (13.3), 3 wire + ground
255405	H-XP2	8 (8.4), 4 wire + ground
255406	H-25	4 (21.2), 2 wire + ground
255407	H-25	6 (13.3), 3 wire + ground
255408	H-25	8 (8.4), 4 wire + ground
253725	H-50	4 (21.2), 2 wire + ground
253726	H-50	4 (21.2), 3 wire + ground
253727	H-50	8 (8.4), 4 wire + ground
256505	H-50	4 (21.2), 3 wire + ground
256506	H-50	6 (13.3), 4 wire + ground

a.230V, 1 phase: Using 5/32 or 4 mm hex allen wrench, connect two power leads to L1 and L2. Connect green to ground (GND).

GND

L1

L2

ti2515b

b.230V, 3 phase: Using 5/32 or 4 mm hex allen wrench, connect three power leads to L1, L2, and L3. Connect green to ground (GND).

GND

L1

L2

L3

ti3248b

312062W

25

Image 25

Contents Operation Important Safety InstructionsContents Systems GCP2R2 Series ModelsApprovals XP2 SeriesSupplied Manuals Reactor Electrical DiagramsReactor Hydraulic Proportioner Part Description Part DescriptionRelated Manuals Electric Shock Hazard Skin Injection Hazard Pressurized Aluminum Parts Hazard Isocyanate Conditions Important Two-Component Material InformationMaterial Self-ignition Keep Components a and B SeparateChanging Materials Foam Resins with 245 fa Blowing AgentsKey for FIG Typical Installation, with circulationSide Supply Detail Side Supply Detail MTypical Installation, without circulation Typical Installation, without circulationComponent Identification Detail of Serial No Plate inside cabinet Detail of Reactor Fluid Manifold shroud removed for clarityMain Power Switch Temperature Controls and IndicatorsRed Stop Button Target Temperature Key/LED Actual Temperature Key/LEDTemperature Scale Keys/LEDs Temperature Arrow KeysSize Component Circuit BreakersMotor ON/OFF Key/LED PSI/BAR Keys/LEDs Motor Controls and IndicatorsPark Key/LED Pressure Key/LEDCycle Count Key/LED Spray AdjustmentsHydraulic Pressure Control Knob Motor Control Arrow KeysLocate Reactor SetupGeneral equipment guidelines Electrical Requirements KW/Full Load Amps Phase Amps WattsElectrical Requirements Full Load Voltage Peak System PartCord Specification Power Cord RequirementsConnect electrical cord Part Model AWG mmConnect feed pumps Connect pressure relief lines Install Fluid Temperature Sensor FTSClose gun fluid manifold valves a and B Connect heated hoseConnect whip hose to gun fluid mani- fold Pressure check hoseGround system Lubrication system setupCheck hydraulic fluid level Check generator fuel level StartupSet temperatures Manual current control mode only Set pressure Change pressure imbalance setting optionalPSI BAR Available Pressure Imbalance SettingsSpraying Open gun fluid manifold valves a and B Standby Shutdown Pressure Relief Procedure Lation Fluid CirculationCirculation Through Gun Manifold Code Code Name Alarm Zone Diagnostic CodesCode Code Name Alarm or Motor Control Diagnostic CodesFrequency of Oil Changes Ambient Recommended Temperature MaintenanceFluid Inlet Strainer Fluid Inlet Strainer ScreenPump Lubrication System Pump Lubrication SystemFlushing Dimension In. mm DimensionsTop View Category Data Technical DataFoam Performance Chart Performance ChartsCoatings Performance Chart Flow Rate in gpm lpm 110Graco Information Graco Standard Warranty