Graco Official Manual for Paint Sprayer: H25, H40, H50 User Guide

Page 22

Cycle Count Key/LED

Press to display cycle count.

To clear counter, press and hold for 3 sec.

Hydraulic Pressure Control Knob

Use to adjust hydraulic pressure available to the hydraulic drive system. Turn knob (HC) clockwise to increase pressure and counter- clockwise to decrease pressure. Use hydraulic pressure gauge (HP, page 17) to view hydrau- lic pressure.

+-

ti7731ati7732a

Component A and B outlet pressures will be higher than the hydraulic set pressure, depending on the model (see Pressure Ratio data; Systems, page 3). Component A and B pressure may be viewed on the pressure gauges (GA, GB), or the higher of the two pressures may be displayed on the motor control panel (MC). See FIG. 3, page 17.

Motor Control Arrow Keys

Use or to:

Adjust pressure imbalance settings, page 33.

Adjust standby settings, page 37.

Spray Adjustments

Spray Adjustments

Flow rate, atomization, and amount of over- spray are affected by four variables.

Fluid pressure setting. Too little pressure results in an uneven pattern, coarse droplet size, low flow, and poor mixing. Too much pressure results in excessive overspray, high flow rates, difficult control, and exces- sive wear.

Fluid temperature. Similar effects to fluid pressure setting. The A and B tempera- tures can be offset to help balance the fluid pressure.

Mix chamber size. Choice of mix chamber is based on desired flow rate and fluid vis- cosity.

Clean-off air adjustment. Too little clean-off air results in droplets building up on the front of the nozzle, and no pattern containment to control overspray. Too much clean-off air results in air-assisted atomization and excessive overspray.

22

312062W

Image 22
Contents Important Safety Instructions OperationContents Systems GCP2R2 Models SeriesXP2 Series ApprovalsReactor Hydraulic Proportioner Part Description Reactor Electrical DiagramsSupplied Manuals Part DescriptionRelated Manuals Electric Shock Hazard Skin Injection Hazard Pressurized Aluminum Parts Hazard Material Self-ignition Important Two-Component Material InformationIsocyanate Conditions Keep Components a and B SeparateFoam Resins with 245 fa Blowing Agents Changing MaterialsSide Supply Detail Typical Installation, with circulationKey for FIG Side Supply Detail MTypical Installation, without circulation Typical Installation, without circulationComponent Identification Detail of Reactor Fluid Manifold shroud removed for clarity Detail of Serial No Plate inside cabinetMain Power Switch Temperature Controls and IndicatorsRed Stop Button Temperature Scale Keys/LEDs Actual Temperature Key/LEDTarget Temperature Key/LED Temperature Arrow KeysCircuit Breakers Size ComponentPark Key/LED Motor Controls and IndicatorsMotor ON/OFF Key/LED PSI/BAR Keys/LEDs Pressure Key/LEDHydraulic Pressure Control Knob Spray AdjustmentsCycle Count Key/LED Motor Control Arrow KeysLocate Reactor SetupGeneral equipment guidelines Electrical Requirements Phase Amps WattsElectrical Requirements KW/Full Load Amps Full Load Voltage Peak System PartConnect electrical cord Power Cord RequirementsCord Specification Part Model AWG mmConnect feed pumps Install Fluid Temperature Sensor FTS Connect pressure relief linesConnect whip hose to gun fluid mani- fold Connect heated hoseClose gun fluid manifold valves a and B Pressure check hoseGround system Lubrication system setupCheck hydraulic fluid level Startup Check generator fuel levelSet temperatures Manual current control mode only Change pressure imbalance setting optional Set pressureAvailable Pressure Imbalance Settings PSI BARSpraying Open gun fluid manifold valves a and B Standby Shutdown Pressure Relief Procedure Fluid Circulation LationCirculation Through Gun Manifold Diagnostic Codes Code Code Name Alarm ZoneMotor Control Diagnostic Codes Code Code Name Alarm orMaintenance Frequency of Oil Changes Ambient Recommended TemperatureFluid Inlet Strainer Screen Fluid Inlet StrainerPump Lubrication System Pump Lubrication SystemFlushing Dimension In. mm DimensionsTop View Technical Data Category DataFoam Performance Chart Performance ChartsCoatings Performance Chart 110 Flow Rate in gpm lpmGraco Standard Warranty Graco Information