Graco H40, H50, H25 Motor Control Diagnostic Codes, Code Code Name Alarm or

Page 43

Diagnostic Codes

Motor Control Diagnostic Codes

Motor control diagnostic codes E21 through E27 appear on pressure display.

There are two types of motor control codes: alarms and warnings. Alarms take priority over warnings.

See repair manual for corrective action.

Alarms

Alarms turn off the motor and heat zones. Turn

main power OFF

then ON

to

clear.

Alarms can also be cleared, except for

code 23, by pressing .

Code 24 (pressure imbalance) is set to an alarm default of 500 psi (3.5 MPa, 35 bar). To change to a warning, see Reac- tor Repair-Parts manual 312063. To change the default pressure imbalance setting, see page 33.

Warnings

Reactor will continue to run. Press to

clear. A warning will not recur for a predeter- mined amount of time (varies for different warnings), or until main power is turned OFF

 

then ON

.

 

 

 

 

Code

Code Name

Alarm or

No.

 

 

Warning

 

 

 

 

 

 

21

No transducer (component A)

Alarm

 

 

 

22

No transducer (component B)

Alarm

 

 

 

 

23

High pressure

 

Alarm

 

 

 

24

Pressure imbalance

Selectable;

 

 

 

see repair

 

 

 

manual

 

 

 

27

High motor temperature

Alarm

 

 

 

30

Momentary loss of communi-

Alarm

 

cation

 

 

 

 

 

31

Pumpline switch failure/high

Alarm

 

cycle rate

 

 

 

 

 

99

Loss of communication

Alarm

 

 

 

 

312062W

43

Image 43
Contents Operation Important Safety InstructionsContents Systems GCP2R2 Series ModelsApprovals XP2 SeriesPart Description Reactor Electrical DiagramsSupplied Manuals Reactor Hydraulic Proportioner Part DescriptionRelated Manuals Electric Shock Hazard Skin Injection Hazard Pressurized Aluminum Parts Hazard Keep Components a and B Separate Important Two-Component Material InformationIsocyanate Conditions Material Self-ignitionChanging Materials Foam Resins with 245 fa Blowing AgentsSide Supply Detail M Typical Installation, with circulationKey for FIG Side Supply DetailTypical Installation, without circulation Typical Installation, without circulationComponent Identification Detail of Serial No Plate inside cabinet Detail of Reactor Fluid Manifold shroud removed for clarityMain Power Switch Temperature Controls and IndicatorsRed Stop Button Temperature Arrow Keys Actual Temperature Key/LEDTarget Temperature Key/LED Temperature Scale Keys/LEDsSize Component Circuit BreakersPressure Key/LED Motor Controls and IndicatorsMotor ON/OFF Key/LED PSI/BAR Keys/LEDs Park Key/LEDMotor Control Arrow Keys Spray AdjustmentsCycle Count Key/LED Hydraulic Pressure Control KnobLocate Reactor SetupGeneral equipment guidelines Full Load Voltage Peak System Part Phase Amps WattsElectrical Requirements KW/Full Load Amps Electrical RequirementsPart Model AWG mm Power Cord RequirementsCord Specification Connect electrical cordConnect feed pumps Connect pressure relief lines Install Fluid Temperature Sensor FTSPressure check hose Connect heated hoseClose gun fluid manifold valves a and B Connect whip hose to gun fluid mani- foldGround system Lubrication system setupCheck hydraulic fluid level Check generator fuel level StartupSet temperatures Manual current control mode only Set pressure Change pressure imbalance setting optionalPSI BAR Available Pressure Imbalance SettingsSpraying Open gun fluid manifold valves a and B Standby Shutdown Pressure Relief Procedure Lation Fluid CirculationCirculation Through Gun Manifold Code Code Name Alarm Zone Diagnostic CodesCode Code Name Alarm or Motor Control Diagnostic CodesFrequency of Oil Changes Ambient Recommended Temperature MaintenanceFluid Inlet Strainer Fluid Inlet Strainer ScreenPump Lubrication System Pump Lubrication SystemFlushing Dimension In. mm DimensionsTop View Category Data Technical DataFoam Performance Chart Performance ChartsCoatings Performance Chart Flow Rate in gpm lpm 110Graco Information Graco Standard Warranty